manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 161

Test Setup - Test Configurator, Timer, and System

Power Blazer

149

Clock

Ext Clock In 

Note:

Available when the 

Clock Mode

 is set to 

External

.

Allows setting the external clock for test synchronization.

Interface Type

 allows the selection of the clock interface: 

DS1

(default), 

E1

, 

2MHz

 (default when DS1 is not supported), or 

1PPS

. 

1PPS

 is automatically selected for 

Dual Test Set

 in 

One-Way Latency

 

measurement mode. 

Ext Clock In

 on a green background indicates that a valid clock is 

received. 

LOS

 on a red background indicates that the received clock is not valid. 

Connector

, available on 8870/8880, either indicates that the BNC 

connector type is used for the clock or on 8880 allows the selection of 

Bantam

 or 

RJ48C

 when the BNC connector is used by the test 

application. The module connector blue LED used for Ext Clock In is 
flashing. 

Termination

 mode specifies how the module is connected to the 

synchronization signal. The 

Termination

 mode is set to 

TERM

 for 2MHz 

and configurable for DS1 and E1. 

For DS1:

TERM

 provides an input that terminates the DS1 signal. 

DSX-MON

 provides high-input impedance and compensation for 

resistive loss. This setting is useful for monitoring DS1 signals at 
DSX monitor points, which are resistor-isolated. 

BRIDGE

 provides high-input impedance for bridging lines that are 

already terminated. This setting is useful for bridging directly 
across copper cable pairs. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands