manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 652

Test Control

640

88000 Series

Lpbk Tool Button (Loopback Tool)

Lpbk Tool Button (Loopback Tool) 

The Loopback Tool provides the capability of looping back the Ethernet 
frames/packets that are received on the loopback tool port. 

Pressing the 

Lpbk Tool

 button opens the Loopback Tool pop-up and 

powers up the port unused by the main test application (it does not start 
looping back the frames yet). The Loopback Tool starts looping back the 
Ethernet frames/packets that are received when pressing on the 

Loopback

 

button from the 

Loopback Tool

 tab. 

Note:

The 

Lpbk

 

Tool

 button is available when the main test application is any 

single port Ethernet test application (up to 10G WAN rate) with the 
exception of Through mode. Not available on 88200NGE. 

Note:

The Loopback Tool is independent from the main test 

Start/Stop

, 

Reset

 

and 

Test Timer

. 

Note:

Enabling/disabling the Laser control affects both the main test application 
and the Loopback Tool when applicable (if both test and tool are using an 
optical port). 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands