Suzuki Liana RH413, Service Manual

Page: 261 / 1302

Engine Mechanical: 1D-56
Specifications
Tightening Torque Specifications
S3RH0A1407001
NOTE
The specified tightening torque is also described in the following.
“Throttle Body Components”
“Throttle Body and Intake Manifold Components”
“Engine Mountings Components”
“Timing Chain Cover Components”
“Timing Chain and Chain Tensioner Components”
“Camshaft, Tappet and Shim Components”
“Valves and Cylinder Head Components”
“Pistons, Piston Rings and Connecting Rods Components”
“Main Bearings, Crankshaft and Cylinder Block Components”
Reference:
For the tightening torque of fastener not specified in this section, refer to “Fasteners Information in Section 0A”.
Fastening part
Tightening torque
Note
N
⋅
m kgf-m lb-ft
Camshaft housing bolt
8 0.8 6.0
(for tightening of
special tool)
)
Camshaft housing bolt 11 1.1 8.0
)
Intake manifold bolt and nut 25 2.5 18.0
)
Cylinder head cover bolt Tighten 8 N
⋅
m (0.8 kgf-m, 6.0 lb-ft) by the
specified procedure
)
Engine cover bolt Tighten 8 N
⋅
m (0.8 kgf-m, 6.0 lb-ft) by the
specified procedure
)
Engine left mounting bolt 55 5.5 40.0 )
Engine right mounting bracket nut 75 7.5 54.5 )
Timing chain cover bolt 23 2.3 17.0 )
Crankshaft pulley bolt 150 15.0 108.5 )
Timing chain No.1 guide bolt 9 0.9 6.5 )
Timing chain tensioner bolt 22 2.2 16.0 )
Timing chain tensioner adjuster bolt 11 1.1 8.0 )
Camshaft housing bolt Tighten 11 N
⋅
m (1.1 kgf-m, 8.0 lb-ft) by the
specified procedure
) / )
Venturi plug 5 0.5 3.5 )
Cylinder head bolt for M10 Tighten 20 N
⋅
m (2.0 kgf-m, 14.5 lb-ft), 40
N
⋅
m (4.0 kgf-m, 29.0 lb-ft), 60
°
and 60
°
by
the specified procedure
)
Cylinder head bolt for M8 Tighten 22 N
⋅
m (2.2 kgf-m, 16.0 lb-ft) by the
specified procedure
)
Connecting rod bearing cap nut Tighten 15 N
⋅
m (1.5 kgf-m, 11.0 lb-ft), 45
°
and 45
°
by the specified procedure
) / )
Sensor plate bolt 11 1.1 8.0 )
Crankshaft bearing cap No.1 bolt ((1) – (10)) Tighten 30 N
⋅
m (3.0 kgf-m, 22.0 lb-ft), 50
N
⋅
m (5.0 kgf-m, 36.5 lb-ft) and 60
°
by the
specified procedure
) / ) / )
Crankshaft bearing cap No.2 bolt ((11) – (20)) Tighten 22 N
⋅
m (2.2 kgf-m, 16.0 lb-ft) by the
specified procedure
) /
)
/
)
Rear oil seal housing bolt 11 1.1 8.0
)
Flywheel or drive plate bolt 70 7.0 51.0
)