manualshive.com logo in svg

Omron CS1W-MC221 -, Operation Manual

Share
Download
Omron CS1W-MC221 - Operation Manual Download Page 354

327

PTP Control

Section 6-2

6-2

PTP Control

Overview

Mode:

 Automatic; 

Method:

 G language (G00)

Positioning each axis independently from the other axes is called PTP control.
Each axis moves at the preset feed rates: at the acceleration for the preset
acceleration time, the maximum feed rate, and the deceleration for the preset
deceleration time. For details on using PTP control with the G language, refer
to 

7-3-1 G00: POSITIONING

.

For example, suppose a control program is executed for moving from the ori-
gin to the X-axis coordinate of 100 and Y-axis coordinate of 50. If the feed
rates, the acceleration times, and the deceleration times are the same for both
axes, X-axis and Y-axis movements will be as illustrated below.

Both the X axis and Y axis move to a coordinate of 50 over the same duration
of time. At this point, the Y axis stops and the X axis moves to a coordinate of
100. 

Jogging in the Manual Mode is also performed using PTP control using the
maximum jogging feed rate.

Error counter reset

Forcibly resets the error counter to zero, 
and stops axis operation.

Automatic, 
manual

Bit designation

351

Servo-lock

Creates a position loop at the MC Unit.

Manual

Bit designation

353

Servo-unlock

Releases the position loop at the MC 
Unit.

Automatic, 
manual

Bit designation

353

Backlash correction

Compensates for backlash in the 
mechanical system.

Automatic, 
manual

Command Area 
designation, CX-Motion

356

Automatic loading

Downloads G-language programs, 
position data, and system parameters to 
the MC Unit from an external memory 
device connected to a personal 
computer running CX-Motion.

Automatic, 
manual

Command Area 
designation, CX-Motion

359

Present position preset

Presets the present position to any 
specified value.

Manual

Command Area 
designation

363

Electronic gear

Sets the per/pulse ratio for an MPG or 
sync encoder.

Manual

System parameter setting 
(by IOWR or CX-Motion)

365

Acceleration/deceleration 
curve

Specifies the acceleration and 
deceleration method for how each axis 
is started or stopped.

Automatic, 
manual

System parameter setting 
(by CX-Motion only)

369

Unlimited feeding

Specifies control for an axis to be fed 
continuously, such as for a conveyer, for 
example.

Automatic, 
manual

System parameter setting 
(by CX-Motion only)

370

Stop

Describes how to stop the axis 
operation.

Automatic, 
manual

Bit designation, software 
limit (system parameter), 
external input (emergency 
stop, limit input), etc.

372

Operation name

Basic function

Mode

Execution method

Page

The illustration shows movements when the high-speed feed 
rate for the X axis is set to the same feed rate as the Y axis.

Summary of Contents for CS1W-MC221 -


































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands