Omron CS1W-MC221 - Operation Manual Download Page 35

Page: 35 / 705

Basic Operations

Section 1-3

Cylindrical Robots

1-3-1

Motion Control

The MC Unit offers the following three types of motion control:

PTP Control
CP Control (linear interpolation and circular interpolation)
Interrupt Feeding

Control programs are created in the G language.

PTP Control

PTP control is used to control each axis (X and Y axis) independently. Posi-
tioning time depends on the travel distance and speed of each axis.

Example:

Moving from the origin to the X-axis coordinate of 100 and Y-axis

coordinate of 50 at the same speed.

Two-axis robot

Three-axis robot

Four-axis robot

X: Although point-to-point control is

possible, linear and circular
interpolation are not possible for
the ends of the robot arms.

Positioning is executed separately for each
axis, so travel between the two points is
carried out as shown in the diagram.

Summary of Contents for CS1W-MC221 -


































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CS1W-MC221 -

Reviews:

Brands by name

Popular brands

Omron CS1W-MC221 -, Operation Manual

Search results

Summary of Contents for CS1W-MC221 -

Reviews:

Brands by name

Popular brands