16 - 36
Chapter 16 Troubleshooting
Classification
of errors
Error
code
Error name
Error
Operation status at error occurrence
Parameter
setting range
errors
903
Outside unit
magnification range
• The set value of the basic parameter 1
"Unit magnification" is outside the setting
range.
• "Movement amount per rotation (AL)" ×
"Unit magnification (AM)" exceeds
2147483648.
The READY signal [X0] is not turned ON.
906
Outside bias speed
range
• The set value of the basic parameter 1
"Bias speed at start" is outside the setting
range.
• The bias speed exceeds the speed limit.
907
Outside electronic gear
setting range
The set value of the electronic gear is
outside the setting range.
910
Outside speed limit
value range
• The set value of the basic parameter 2
"Speed limit value" is outside the setting
range.
• The speed limit value is smaller than the
OPR speed.
When the PLC READY signal [Y0] is turned
from OFF to ON
: READY signal [X0] is not turned
ON.
At start
: The system does not operate.
911
Outside acceleration
time 0 range
The set value of the basic parameter 2
"Acceleration time 0" is outside the setting
range.
912
Outside deceleration
time 0 range
The set value of the basic parameter 2
"Deceleration time 0" is outside the setting
range.
920
Backlash
compensation amount
error
The calculation result of the following
equation is smaller than 0 or larger than
4194304.
0
≤
Pr.11
×
Pr.2
Pr.3
×
Pr.4
≤
4194303
The READY signal [X0] is not turned ON.
921
Software stroke limit
upper limit
• In the unit of "degree", the set value of the
detailed parameter 1 "Software stroke
limit upper limit value" is outside the
setting range.
• In a unit other than "degree", the software
stroke limit upper limit value is smaller
than the software stroke limit lower limit
value.
922
Software stroke limit
lower limit
• In the unit of "degree", the set value of the
detailed parameter 1 "Software stroke
limit lower limit value" is outside the
setting range.
• In a unit other than "degree", the software
stroke limit upper limit value is smaller
than the software stroke limit lower limit
value.
Summary of Contents for MELSEC-L Series
