manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

313 

 

 

 

rc_w0 

rc_w0 

 

r 

r 

r 

 

Bits   

Fields 

Descriptions 

31:7 

Reserved 

Must  be kept  at reset value. 

6 

SEIF 

Seed error interrupt  flag 

This bit w ill be set if more than 64 consecutive same bit or more than 32 consecutive 

01(or 10) changing  are detected. 

0: No fault detected 

1: Seed error has been detected.  The bit is cleared by w riting 0. 

5 

CEIF 

Clock  error interrupt  flag 

This bit w ill be set if TRNG_CLK  frequency is low er than 1/16 HCLK  frequency. 

0: No fault detected 

1: Clock  error has been detected. The  bit is cleared by w riting 0. 

4:3 

Reserved 

Must  be kept  at reset value. 

2 

SECS 

Seed error current status 

0:  Seed  error is  not  detected  at  current time.  In  case of SEIF=1  and  SECS=0,  it 

means  seed error has been detected before but now  is recovered. 

1: Seed  error is detected  at current time  if more  than  64 consecutive same  bits or 

more  than 32 consecutive 01(or 10) changing  are detected 

1 

CECS 

Clock  error current status 

0: Clock  error is not  detected  at current time.  In  case of CEIF=1  and  CECS=0,  it 

means  clock error has been detected before but now  is recovered. 

1: Clock  error is detected at current time.  TRNG_CLK  frequency is low er than 1/16 

HCLK  frequency. 

0 

DRDY 

Random  data  ready  status  bit.  This  bit  is  cleared  by  reading  the  TRNG_DA TA  

register and set w hen a new  random  number  is generated. 

0: The content of TRNG  data register is not available. 

1: The content of TRNG  data register is available. 

11.4.3. 

Data register (TRNG_DATA)

 

Address offset: 0x08 

Reset value: 0x0000 0000 

Application must make sure DRDY is set before reading this register 

This register has to be accessed by word (32-bit). 

31 

30 

29 

28 

27 

26 

25 

24 

23 

22 

21 

20 

19 

18 

17 

16 

TRNDATA[31:16] 

r 

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

Dahua DHI-NVR5224-24P-4KS2 Quick Start Manual preview
DHI-NVR5224-24P-4KS2
Brand: Dahua Pages: 24
PaloAlto Networks PA-7500 Quick Start Manual preview
PA-7500
Brand: PaloAlto Networks Pages: 3
Z3 Technology Z3-DM8168-PCI-RPS Manual preview
Z3-DM8168-PCI-RPS
Brand: Z3 Technology Pages: 20
Z3 Technology Z3-DM8107-SDI2-RPS User Manual preview
Z3-DM8107-SDI2-RPS
Brand: Z3 Technology Pages: 75
Z-Wave USB Dongle User Manual preview
USB Dongle
Brand: Z-Wave Pages: 13
A10 Thunder Series Manual preview
Thunder Series
Brand: A10 Pages: 52
Lochinvar Armor 101 Series Instructions Manual preview
Armor 101 Series
Brand: Lochinvar Pages: 28
Lochinvar Armor 101 Series Service Manual preview
Armor 101 Series
Brand: Lochinvar Pages: 44
Juniper NFX250 Quick Start Manual preview
NFX250
Brand: Juniper Pages: 7
Lindsay Broadband LBON320AC Series Installation And Operation Manual preview
LBON320AC Series
Brand: Lindsay Broadband Pages: 4
Z-Wave RAZBERRY 7 PRO Quick Start Manual preview
RAZBERRY 7 PRO
Brand: Z-Wave Pages: 6
Dahua D-NVR4108HS-4KS2/L Quick Start Manual preview
D-NVR4108HS-4KS2/L
Brand: Dahua Pages: 33
mikroElektronika Pressure click Quick Start Manual preview
Pressure click
Brand: mikroElektronika Pages: 2
AXIOMTEK CEM500 Quick Installation Manual preview
CEM500
Brand: AXIOMTEK Pages: 2
Vecow SPC-2845 User Manual preview
SPC-2845
Brand: Vecow Pages: 61
B&B Electronics PCMCIA High Speed Serial Card CE 232HSPCC User Manual preview
PCMCIA High Speed Serial Card CE 232HSPCC
Brand: B&B Electronics Pages: 14
ST STA309A Operation Manual preview
STA309A
Brand: ST Pages: 67
Vivotek ND8212W Hardware Installation Manual preview
ND8212W
Brand: Vivotek Pages: 46

Brands by name

Popular brands

Load more brands