manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

810 

 

 

1: CE-ATA  enable 

13 

NINTEN 

No  CE-ATA  Interrupt  (CE-ATA  only) 

This  bit defines if there is CE-ATA  interrupt or not.  This bit  is only used w hen CE-

ATA card. 

0: CE-ATA  interrupt enable 

1: CE_ATA  interrupt  disable 

12 

ENCMDC 

CMD  completion  signal  enabled  (CE-ATA  only) 

This bit defines if there is command  completion  signal or not in CE-ATA  card. 

0: no completion  signal 

1: have completion  signal 

11 

SUSPEND 

SD  I/O  suspend command(SD  I/O  only) 

This  bit  defines w hether the  CSM  to send a suspend  command  or not.  This  bit  is 

only used for SDIO  card. 

0: no effect 

1: suspend command 

10 

CSMEN 

Command  state machine  (CSM)  enable  bit 

0: Command  state machine  disable (stay on CS_Idle) 

1: Command  state machine  enable 

9 

WAITDEND 

Waits for ends of data transfer. 

If this bit  is set, the command  state machine  starts to send a command  must  w ait 

the end of data transfer. 

0: no effect 

1: Wait the end of data transfer 

8 

INTWAIT 

Interrupt  w ait instead  of timeout 

This bit defines the command  state machine  to w ait card interrupt at CS_Wait  state 

in command  state machine.  If this bit is set, no command  w ait timeout  generated. 

0: Not w ait interrupt. 

1: Wait interrupt. 

7:6 

CMDRESP[1:0] 

Command  response type bits 

These bits define the response type after sending  a command  message. 

00: No response 

01: Short response 

10: No response 

11: Long response 

5:0 

CMDIDX[5:0] 

Command  index 

This field defines the command  index to be sent to SDIO  card. 

Note: 

Betw een Tw o w rite accesses to this register, it  needs at least 3 SDIOCLK  + 2 pclk2  w hich used 

to sync the registers to SDIOCLK  clock domain.

 

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

QSC DSP-30 Hardware Manual preview
DSP-30
Brand: QSC Pages: 28
Paradyne 7995-A2-374 Quick Installation Instructions preview
7995-A2-374
Brand: Paradyne Pages: 1
Fostex DE-1 Service Manual preview
DE-1
Brand: Fostex Pages: 20
ebm-papst D3G146-LT13-30 Operating Instructions Manual preview
D3G146-LT13-30
Brand: ebm-papst Pages: 11
YASKAWA PG-Z2 Instructions Manual preview
PG-Z2
Brand: YASKAWA Pages: 15
DAD DXZ48 User Manual preview
DXZ48
Brand: DAD Pages: 16
Addonics Technologies ADSA2 Installation Manual preview
ADSA2
Brand: Addonics Technologies Pages: 1
Omron ACCURAX G5 - Quick Start Manual preview
ACCURAX G5 -
Brand: Omron Pages: 13
EMS 2000 IDU Series User Manual preview
2000 IDU Series
Brand: EMS Pages: 52
B&B Electronics 4 Channel Input Buffer Board SDAIBB Product Manual preview
4 Channel Input Buffer Board SDAIBB
Brand: B&B Electronics Pages: 22
CNC4PC C52- ESS User Manual preview
C52- ESS
Brand: CNC4PC Pages: 11
Vecow SPC-2845 User Manual preview
SPC-2845
Brand: Vecow Pages: 61
Patton electronics ipRocketLink IAD 3086 Quick Start Manual preview
ipRocketLink IAD 3086
Brand: Patton electronics Pages: 12
ADTRAN ENHANCED PSD 239 H2R Product Manual preview
ENHANCED PSD 239 H2R
Brand: ADTRAN Pages: 2
WatchNet ENM-04 POE Quick Connection Manual preview
ENM-04 POE
Brand: WatchNet Pages: 2
G&D DP1.2-Vision-IP-Fiber Installation And Operation Manual preview
DP1.2-Vision-IP-Fiber
Brand: G&D Pages: 240
TP-Link VIGI Quick Start Manual preview
VIGI
Brand: TP-Link Pages: 2
Boardcon Embedded Design EM3568 User Manual preview
EM3568
Brand: Boardcon Embedded Design Pages: 36

Brands by name

Popular brands

Load more brands