manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

333 

 

 

access error interrupt, single-data mode exception interrupt, and FIFO error  and exception 

interrupt. A DMA channel interrupt may be produced when any interrupt event occurs on the 

channel.   

Each interrupt event  has a  dedicated flag bit in the DMA_INTF0 or DMA_INTF1 register, a 

dedicated clear bit in the DMA_INTC0 and DMA_INTC1 register, and a dedicated enable bit 

in the DMA_CHxCTL and CHxFCTL register, as described in the 

Table 12-6. DMA interrupt 

events

. 

Table 12-6. DMA interrupt events 

Interrupt event 

Flag bit 

Enable bit 

Clear bit 

DMA_INTF0 or 

DMA_INTF1 

DMA_CHxCTL  or 

DMA_CHxFCTL 

DMA_INTC0 or 

DMA_INTC1 

Full  transfer finish 

FTFIF 

FTFIE 

FTFIFC 

Half transfer finish 

HTFIF 

HTFIE 

HTFIFC 

Transfer access error 

TAEIF 

TAEIE 

TAEIFC 

Single-data  mode 

exception 

SDEIF 

SDEIE 

SDEIFC 

FIFO  error and 

exception 

FEEIF 

FEEIE 

FEEIFC 

These five  events can be divided  into three types:  

 

Flag: Full transfer finish flag and half transfer finish flag 

 

Exception: Single-data mode exception and FIFO exception 

 

Error: Transfer access error and FIFO error 

When  the  exception events  occur, the  DMA  transmission is  not  affected  and  continues 

transferring normally. When the error events are detected, the DMA transmission is stopped. 

These three types of event are described in detail in the following sections.  

12.5.1. 

Flag 

Two flag events are supported, including full transfer finish flag and half transfer finish flag.  

The full transfer finish flag is asserted, when one of the following situations occurs: 

 

The CNT bits reach to zero when DMA is the transfer flow controller. 

 

When peripheral is the transfer flow controller, the last request is responded completely 

and the contents of the FIFO are entirely written into the memory in peripheral-to-memory 

mode. 

 

When the channel is disabled by software before  the  end of  the transfer, the current 

memory and peripheral is completed and the contents of the FIFO are  entirely written 

into the memory in peripheral-to-memory or memory-to-memory mode. 

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

dbx 902 Manual preview
902
Brand: dbx Pages: 8
Cabletron Systems MMAC-5FNB Overview And Setup Manual preview
MMAC-5FNB
Brand: Cabletron Systems Pages: 21
Dahua DHI-NVR5224-24P-4KS2 Quick Start Manual preview
DHI-NVR5224-24P-4KS2
Brand: Dahua Pages: 24
Hama 39707 Operating Instruction preview
39707
Brand: Hama Pages: 4
IEI Technology PCIE-Q470 Quick Installation Manual preview
PCIE-Q470
Brand: IEI Technology Pages: 19
IEI Technology KINO-DH420 User Manual preview
KINO-DH420
Brand: IEI Technology Pages: 87
IEI Technology HPE-4S2 Quick Installation Manual preview
HPE-4S2
Brand: IEI Technology Pages: 3
Radwin Transportation FiberinMotion Deployment Manual preview
Transportation FiberinMotion
Brand: Radwin Pages: 122
Zenith Data Systems Z-100 Series Installation Manual preview
Z-100 Series
Brand: Zenith Data Systems Pages: 64
Texas Instruments ThunderLAN TNETE100A Programmer'S Manual preview
ThunderLAN TNETE100A
Brand: Texas Instruments Pages: 179
Behringer EXPANSION CARD X-DANTE Quick Start Manual preview
EXPANSION CARD X-DANTE
Brand: Behringer Pages: 65
A4Tech RG-71M User Manual preview
RG-71M
Brand: A4Tech Pages: 7
Adaptec AAA-130SA SERIES Installation And Hardware Manual preview
AAA-130SA SERIES
Brand: Adaptec Pages: 94
IndigoVision Compact NVR-AS 4000 User Manual preview
Compact NVR-AS 4000
Brand: IndigoVision Pages: 38
Stahl HFisolator 9730/26-11 Operating Instructions preview
HFisolator 9730/26-11
Brand: Stahl Pages: 2
Intel BX80637I53570K Specification preview
BX80637I53570K
Brand: Intel Pages: 54
Aaeon GENE-EHL7 User Manual preview
GENE-EHL7
Brand: Aaeon Pages: 119
RR-Concepts StationMaster Manual preview
StationMaster
Brand: RR-Concepts Pages: 12

Brands by name

Popular brands

Load more brands