manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

74 

 

 

2.4.6. 

Main flash  programming 

The FMC provides a 32-bit word programming function by DBUS which is used to modify the 

main Flash memory contents. Operate secure Flash or non-secure Flash using secure or 

non-secure registers. 

The following steps show the register access sequence of the programming operation.   

 

Unlock the FMC_CTL/FMC_SECCTL register if necessary. 

 

Check the BUSY/SECBUSY bit in the FMC_STAT/FMC_SECSTAT register to confirm 

that no Flash memory operation is in progress (BUSY/SECBUSY equals to 0). Otherwise, 

wait until the operation has finished. 

 

Set the PG/SECPG bit in the FMC_CTL/FMC_SECCTL register.  

 

Write the data to be programed with desired absolute address (0x08XX XXXX/0x0CXX 

XXXX).   

 

Wait  until  all  the  operations  have  been  finished  by  checking  the  value  of  the 

BUSY/SECBUSY bit in the FMC_STAT/FMC_SECSTAT register.   

 

Read and verify the Flash memory using a DBUS access if required.  

When  the  operation  is  executed  successfully,  the  ENDF/SECENDF  bit  in  the 

FMC_STAT/FMC_SECSTAT register is set, and an interrupt will be triggered by FMC if the 

ENDIE bit in the FMC_CTL/FMC_SECCTL register is set. Note that there are some program 

errors need caution: 

Each word can be  programmed only one time after erase and  before next erase. Note that 

the PG/SECPG bit must be set before the word programming operation.  

Additionally, the program operation will be ignored  on erase/program protected pages and 

the WPERR/SECWPERR bit in the FMC_STAT/FMC_SECSTAT will be set.  

In  these conditions, a Flash  operation error  interrupt  will  be  triggered  by the  FMC if  the 

ERRIE/SECERRIE bit in  the  FMC_CTL/FMC_SECCTL register  is  set. The  software  can 

check WPERR/SECWPERR bit in the FMC_STAT/FMC_SECSTAT register to detect which 

condition occurred in the interrupt handler. The following figure 

Figure 2-4. Process of word 

program operation 

shows the word programming operation flow. 

 

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

Dave Embedded Systems ARM Cortex-A9 MPCore Quick Start Manual preview
ARM Cortex-A9 MPCore
Brand: Dave Embedded Systems Pages: 67
Acqiris SA217P Startup Manual preview
SA217P
Brand: Acqiris Pages: 22
Supermicro SAS-827HD User Manual preview
SAS-827HD
Brand: Supermicro Pages: 16
Allnet ALL1682504 Quick Installation preview
ALL1682504
Brand: Allnet Pages: 12
Telebyte 458-LM-E2-36 Quick Start Manual preview
458-LM-E2-36
Brand: Telebyte Pages: 19
Analog Devices EZ-Extender Analog 120-Pin Probing Board Manual preview
EZ-Extender Analog 120-Pin Probing Board
Brand: Analog Devices Pages: 29
Orolia Seven Solutions WR-ZEN Series User Manual preview
Seven Solutions WR-ZEN Series
Brand: Orolia Pages: 167
Supermicro Optane Persistent Memory 200 Series User Manual preview
Optane Persistent Memory 200 Series
Brand: Supermicro Pages: 54
Renesas R0E530650CFJ30 User Manual preview
R0E530650CFJ30
Brand: Renesas Pages: 4
Crystal Vision TANDEM HD-21 User Manual preview
TANDEM HD-21
Brand: Crystal Vision Pages: 54
ebm-papst R3G560-AH02-03 Operating Instructions Manual preview
R3G560-AH02-03
Brand: ebm-papst Pages: 13
Ubiquiti EdgeSwtch 5XP Quick Start Manual preview
EdgeSwtch 5XP
Brand: Ubiquiti Pages: 13
TP-Link VIGI NVR1004H-4P Quick Installation Manual preview
VIGI NVR1004H-4P
Brand: TP-Link Pages: 2
Cypress Semiconductor CY7C68023 Specification Sheet preview
CY7C68023
Brand: Cypress Semiconductor Pages: 9
Promise Technology Pegasus R4 Product Manual preview
Pegasus R4
Brand: Promise Technology Pages: 148
IEI Technology WSB-H610-R11 User Manual preview
WSB-H610-R11
Brand: IEI Technology Pages: 146
RAK RAK1901 Quick Start Manual preview
RAK1901
Brand: RAK Pages: 14
Intellinet 560665 User Manual preview
560665
Brand: Intellinet Pages: 32

Brands by name

Popular brands

Load more brands