manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

537 

 

 

110: PWM  mode0.  When  counting up, O0CPRE  is active as long  as the counter is 

smaller  than  TIMERx_CH0CV  else  inactive.  When  counting  dow n, O0CPRE  is 

inactive as long  as the counter is larger than TIMERx_CH0CV  else active. 

111: PWM  mode1.  When  counting  up,  O0CPRE  is inactive  as long  as the counter  

is  smaller  than  TIMERx_CH0CV  else  active.  When  counting  dow n, O0CPRE  is 

active as long as the counter is larger than TIMERx_C H0CV  else inactive. 

When  configured in PWM  mode,  the O2CPRE  level  changes only w hen the output 

compare  mode  sw itches from  “Timing  mode”  mode  to “PWM”  mode  or w hen the 

result of the comparison  changes. 

3 

CH2COMSEN 

Channel  2 compare  output  shadow  enable 

When this bit is set, the shadow  register of TIMERx_CH2CV  register, w hich updates 

at each update  event w ill be enabled.   

0: Channel  2 output compare  shadow  disable 

1: Channel  2 output compare  shadow  enable 

The  PWM  mode  can be used w ithout validating  the shadow  register only in  single 

pulse mode  (SPM  bit in TIMERx_CTL0  register is set). 

2 

CH2COMFEN 

Channel  2 output  compare  fast enable 

When  this  bit  is  set,  the  effect  of  an  event  on  the  trigger  in  input  on  the 

capture/compare  output  w ill be accelerated if the channel is configured in PWM0  or 

PWM1  mode.  The  output  channel w ill treat an active edge on the trigger input  as a 

compare  match,  and  CH2_O  is set  to  the  compare  level  independently  from  the 

result of the comparison. 

0: Channel  2 output quickly  compare  disable.  The minimum  delay from an edge on 

the trigger input to activate CH2_O  output  is 5 clock cycles. 

1: Channel  2 output  quickly  compare  enable.  The  minimum  delay  from an edge on 

the trigger input to activate CH2_O  output  is 3 clock cycles. 

1:0 

CH2MS[1:0] 

Channel  2 I/O  mode  selection 

This bit-field  specifies the w ork mode  of the channel and the input  signal selection. 

This  bit-field  is  w ritable  only  w hen  the  channel  is  not  active.  (CH2EN  bit  in 

TIMERx_CHCTL2  register is reset).). 

00: Channel  2 is configured as output 

01: Channel  2 is configured as input,  IS2  is connected to CI2FE2 

10: Channel  2 is configured as input,  IS2  is connected to CI3FE2 

11: Channel  2 is configured as input, IS2  is connected to ITS.  This mode  is w orking 

only if an internal  trigger  input  is selected  through  TRGS  bits in TIMERx_S MC F G 

register. 

Input capture m ode: 

Bits   

Fields 

Descriptions  

31:16 

Reserved 

Must  be kept  at reset value. 

15:12 

CH3CAPFLT[3:0] 

Channel  3 input  capture filter control 

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

3Com 486 Getting Started Manual preview
486
Brand: 3Com Pages: 20
3Com 3CRWEASY96A Quick Start Manual preview
3CRWEASY96A
Brand: 3Com Pages: 8
Magma PE6R4-I Quick Installation Manual preview
PE6R4-I
Brand: Magma Pages: 2
SAF Phoenix G2 IDU Quick Start Manual preview
Phoenix G2 IDU
Brand: SAF Pages: 30
Amperes iPX5500 Instruction Manual preview
iPX5500
Brand: Amperes Pages: 8
Garland INT40G2SR44 User Manual preview
INT40G2SR44
Brand: Garland Pages: 43
ZyXEL Communications GS3700 Series Handbook preview
GS3700 Series
Brand: ZyXEL Communications Pages: 215
IFM Electronic OVP800 Operating Instructions Manual preview
OVP800
Brand: IFM Electronic Pages: 14
mikroElektronika Pressure click Quick Start Manual preview
Pressure click
Brand: mikroElektronika Pages: 2
Boss Vocal Performer VE-20 Owner'S Manual preview
Vocal Performer VE-20
Brand: Boss Pages: 20
Commell FS-A79 User Manual preview
FS-A79
Brand: Commell Pages: 36
Vecow SPC-2845 User Manual preview
SPC-2845
Brand: Vecow Pages: 61
Digital Voice Systems VC-20-MR2 User Manual preview
VC-20-MR2
Brand: Digital Voice Systems Pages: 32
ICOP Technology VDX-6354RD User Manual preview
VDX-6354RD
Brand: ICOP Technology Pages: 42
Ultra Products Internal All-in-One Digital Media Drive ULT31793 Specifications preview
Internal All-in-One Digital Media Drive ULT31793
Brand: Ultra Products Pages: 1
Galileo Quark SoC X1000 Getting Started Manual preview
Quark SoC X1000
Brand: Galileo Pages: 20
Lucent Technologies CIB40 Installation Manual preview
CIB40
Brand: Lucent Technologies Pages: 7
RME Audio AI4S-192 AIO User Manual preview
AI4S-192 AIO
Brand: RME Audio Pages: 7

Brands by name

Popular brands

Load more brands