manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

91 

 

 

1: error interrupt  enable 

9:8 

Reserved 

Must  be kept  at reset value. 

7 

SECLK 

FMC_SECCTL  lock bit 

This  bit  is  cleared  by  hardw are w hen  right  sequence  w ritten to  FMC_SEC K EY  

register. 

This bit can be set by softw are. 

6 

SECSTART 

Send erase command  to FMC  bit 

This bit is set by softw are to send erase command  to FMC. 

This bit is cleared by hardw are w hen the BUSY  bit is cleared. 

5:3 

Reserved 

Must  be kept  at reset value. 

2 

SECMER 

Main  Flash mass erase command  bit 

This bit is set or cleared by softw are. 

0: no effect 

1: main  Flash  mass erase command 

1 

SECPER 

Main  Flash page erase command  bit 

This bit is set or clear by softw are. 

0: no effect 

1: main  Flash  page erase command 

0 

SECPG 

Main  Flash program  command  bit 

This bit is set or clear by softw are. 

0: no effect 

1: main  Flash  program  command 

Note: 

This register should be reset after the corresponding Flash operation completed. 

2.5.10. 

Secure Address  register (FMC_SECADDR) 

Address offset: 0x34 

Reset value: 0x0000 0000.   

This  register is  secure. It  can  be  read  and  written  only by  secure access. A non-secure 

read/write access is RAZ/WI. This register can be  protected against non-privileged  access 

when FMC_PRIV = 1. 

This register has to be accessed by word (32-bit). 

31 

30 

29 

28 

27 

26 

25 

24 

23 

22 

21 

20 

19 

18 

17 

16 

SECADDR[31:16] 

W 

15 

14 

13 

12 

11 

10 

9 

8 

7 

6 

5 

4 

3 

2 

1 

0 

SECADDR[15:0] 

W 

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

3Com 3C16080 Important Information preview
3C16080
Brand: 3Com Pages: 2
3Com 3C421600A Quick Setup Manual preview
3C421600A
Brand: 3Com Pages: 74
3Com 3C421600A Installation Manual preview
3C421600A
Brand: 3Com Pages: 6
MA lighting grandMA2 Series Quick Manual preview
grandMA2 Series
Brand: MA lighting Pages: 36
Delta M125HV-113 Quick Installation Manual preview
M125HV-113
Brand: Delta Pages: 2
Direct IP IDIS DR-1304P Operation Manual preview
IDIS DR-1304P
Brand: Direct IP Pages: 76
Lutron Electronics Smart Bridge Quick Start Manual preview
Smart Bridge
Brand: Lutron Electronics Pages: 4
Cisco MERAKI MX450 Installation Manual preview
MX450
Brand: Cisco MERAKI Pages: 4
G&D DL-DVI-Vision-IP Series Installation And Operation Manual preview
DL-DVI-Vision-IP Series
Brand: G&D Pages: 228
Cypress Semiconductor CY62136EV30 MoBL Specification Sheet preview
CY62136EV30 MoBL
Brand: Cypress Semiconductor Pages: 12
Echo LAYLA 3G Owner'S Manual preview
LAYLA 3G
Brand: Echo Pages: 21
TDK HHM Series HHM1521 Specifications preview
HHM Series HHM1521
Brand: TDK Pages: 2
EK EK-Mana MSI MAG Z690 TORPEDO EK X D-RGB User Manual preview
EK-Mana MSI MAG Z690 TORPEDO EK X D-RGB
Brand: EK Pages: 9
Exsys EX-16600 Manual preview
EX-16600
Brand: Exsys Pages: 2
Epson S5U13719P00C100 User Manual preview
S5U13719P00C100
Brand: Epson Pages: 31
Epson S2R72A21 Application Note preview
S2R72A21
Brand: Epson Pages: 34
Epson S1D15722 Series Technical Manual preview
S1D15722 Series
Brand: Epson Pages: 77
Epson S1C63666 Technical Manual preview
S1C63666
Brand: Epson Pages: 171

Brands by name

Popular brands

Load more brands