manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

656 

 

 

1: Host address is enabled,  address  0b0001000x  w ill be acknow ledged. 

19 

GCEN 

Whether  or not to response to a General  Call  (0x00) 

0: Slave w on’t response to a General  Call 

1: Slave w ill response to a General  Call 

18 

WUEN 

Wakeup  from Deep-sleep  mode  enable 

0: Wakeup  from Deep-sleep  mode  disable. 

1: Wakeup  from Deep-sleep  mode  enable. 

Note:

 WUEN  can be set only w hen DNF[3:0]  = 0000. This  bit is reserved in  I2C1. 

17 

SS 

Whether  to stretch SCL  low  w hen data is not ready in slave mode. 

This bit is set and cleared by softw are. 

0: SCL  Stretching is enabled 

1: SCL  Stretching is disabled 

Note: 

When  in  master  mode,  this  bit  must  be  0.  This  bit  can  be  modified  w hen 

I2CEN  = 0. 

16 

SBCTL 

Slave byte control 

This bit is used to enable  hardw are byte control in slave mode. 

0: Slave byte control  is disabled 

1: Slave byte control  is enabled 

15 

DENR 

DMA  enable  for reception 

0: DMA  is disabled  for reception 

1: DMA  is enabled  for reception 

14 

DENT 

DMA  enable  for transmission 

0: DMA  is disabled  for transmission 

1: DMA  is enabled  for transmission 

13 

Reserved 

Must  be kept  at reset value. 

12 

ANOFF 

Analog noise filter disable 

0: Analog noise filter is enabled 

1: Analog noise filter is disabled 

Note: 

This bit can only be programmed  w hen the I2C  is disabled  (I2CEN  = 0). 

11:8 

DNF[3:0] 

Digital  noise filter 

These  bits are used to configure the digital  noise filter on SDA  and SCL  input.  The 

digital  filter w ill filter spikes w ith a length of up to DNF[3:0]  * t

I2CCLK

 

0000: Digital  filter is disabled 

0001: Digital  filter is enabled  and filter spikes w ith a length  of up to 1 t

I2CCLK

 

... 

1111: Digital  filter is enabled  and filter spikes w ith a length  of up to15  t

I2CCLK

 

These bits can only be modified  w hen the I2C  is disabled  (I2CEN  = 0). 

7 

ERRIE 

Error interrupt  enable 

0: Error interrupt disabled 

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

Dahua DHI-NVR5224-24P-4KS2 Quick Start Manual preview
DHI-NVR5224-24P-4KS2
Brand: Dahua Pages: 24
Idis DR-4100P Series Installation Manual preview
DR-4100P Series
Brand: Idis Pages: 30
Tandberg Data RDX QuikStation 4 Quick Start Manuals preview
RDX QuikStation 4
Brand: Tandberg Data Pages: 2
AlphaShield INTERNET PRIVACY PROTECTION (Spanish) Manual Del Usuario preview
INTERNET PRIVACY PROTECTION
Brand: AlphaShield Pages: 49
Garland INT10G10SP2 User Manual preview
INT10G10SP2
Brand: Garland Pages: 6
Gate NanoAAB User Manual preview
NanoAAB
Brand: Gate Pages: 8
Dantel 46020-38 Installation & Operation Manual preview
46020-38
Brand: Dantel Pages: 62
Enterasys Enterasys Matrix 2G4082-25 Hardware Installation Manual preview
Enterasys Matrix 2G4082-25
Brand: Enterasys Pages: 58
Patton electronics FORESIGHT 6300 User Manual preview
FORESIGHT 6300
Brand: Patton electronics Pages: 145
ICP DAS USA I-87K Series User Manual preview
I-87K Series
Brand: ICP DAS USA Pages: 31
UMAX Technologies SuperMac E100 User Manual preview
SuperMac E100
Brand: UMAX Technologies Pages: 27
Cypress Semiconductor CY7C027AV Specification Sheet preview
CY7C027AV
Brand: Cypress Semiconductor Pages: 18
DayTronic PC-HSICA Instruction Manual preview
PC-HSICA
Brand: DayTronic Pages: 13
YASKAWA 040-1CA00 Manual preview
040-1CA00
Brand: YASKAWA Pages: 87
Forcepoint V10000 G4R2 Quick Start Manual preview
V10000 G4R2
Brand: Forcepoint Pages: 2
Adaptec 2025ZCR - SCSI RAID Storage Controller Datasheet preview
2025ZCR - SCSI RAID Storage Controller
Brand: Adaptec Pages: 2
TQ STKa64xxL Quick Start Manual preview
STKa64xxL
Brand: TQ Pages: 2
Omnitron Systems Technology iConverter GX/F User Manual preview
iConverter GX/F
Brand: Omnitron Systems Technology Pages: 2

Brands by name

Popular brands

Load more brands