manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

831 

 

 

Figure 24-8. Device mode FIFO access register map 

IEP0 FIFO Write

 IEP1 FIFO Write

1000h-1FFFh

 IEP3 FIFO Write

...

2000h-2FFFh

4000h-4FFFh

Can be read by any 

OUT endpoint FIFO

 

24.5.6. 

Operation guide 

This section describes the advised operation guide for USBFS. 

Host mode 

Global register initialization sequence 

1. 

Program USBFS_GAHBCS register according to application’s demand, such as  the 
TxFIFO’s empty threshold, etc. GINTEN bit should be kept cleared at this time. 

2. 

Program USBFS_GUSBCS register according to application’s demand, such as  the 
operation mode (host, device or OTG) and some parameters of OTG and USB protocols. 

3. 

Program USBFS_GCCFG register according to application’s demand. 

4.  Program USBFS_GRFLEN, USBFS_HNPTFLEN_DIEP0TFLEN and USBFS_HPTFLEN 

register to configure the data FIFOs according to application’s demand. 

5.  Program USBFS_GINTEN register to enable Mode Fault and Host Port interrupt and set 

GINTEN bit in USBFS_GAHBCS register to enable global interrupt.  

6.  Program USBFS_HPCS register and set PP bit. 

7. 

Wait for a device’s connection, and once a device is connected, the connection interrupt 
PCD in  USBFS_HPCS register will be  triggered. Then  set PRST bit to  perform  a port 

reset. Wait for at least 10ms and then clear PRST bit. 

8.  Wait PEDC interrupt in USBFS_HPCS register and then read PE bit to ensure that the 

port is successfully enabled. Read PS [1:0] bits to get the co

nnected device’s speed and 

then program USBFS_HFT register to change the SOF interval if needed.  

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

ABB i-bus KNX IPR/S 3.5.1 Product Manual preview
i-bus KNX IPR/S 3.5.1
Brand: ABB Pages: 44
Barco EX Safety Manual preview
EX
Brand: Barco Pages: 100
IBM AS/400 Hardware User Manual preview
AS/400
Brand: IBM Pages: 104
IBM System Storage TS3100 Setup, Operator, And Service Manual preview
System Storage TS3100
Brand: IBM Pages: 375
ICP DAS USA I-7532M-FD User Manual preview
I-7532M-FD
Brand: ICP DAS USA Pages: 48
ICP DAS USA WF-2572 User Manual preview
WF-2572
Brand: ICP DAS USA Pages: 24
TFortis Teleport-1 Configuration Manual preview
Teleport-1
Brand: TFortis Pages: 86
hawa HAWA-Frontside 60/B Planning And Installation Instructions preview
HAWA-Frontside 60/B
Brand: hawa Pages: 28
Supero AOC-SIMLC User Manual preview
AOC-SIMLC
Brand: Supero Pages: 68
Enterasys X-Pedition 2000 Getting Started Manual preview
X-Pedition 2000
Brand: Enterasys Pages: 86
Commell CMB-673 Installation Manual preview
CMB-673
Brand: Commell Pages: 9
8e6 Technologies ER3-100 (5K02-55) Quick Start Manual preview
ER3-100 (5K02-55)
Brand: 8e6 Technologies Pages: 74
National Instruments NI-9206 Getting Started preview
NI-9206
Brand: National Instruments Pages: 8
AC Infinity AIRCOM Series User Manual preview
AIRCOM Series
Brand: AC Infinity Pages: 24
Renesas Emulation Memory Board R0E330850MSRC0 User Manual preview
Emulation Memory Board R0E330850MSRC0
Brand: Renesas Pages: 4
DTS XD10P Installation And Operation Manual preview
XD10P
Brand: DTS Pages: 94
Renesas R8C/2F Quick Start Manual preview
R8C/2F
Brand: Renesas Pages: 6
Genexis FiberTwist XGS2410 Installation Manual preview
FiberTwist XGS2410
Brand: Genexis Pages: 7

Brands by name

Popular brands

Load more brands