manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

164 

 

 

0: High  speed crystal oscillator  Pow er dow n 

1: High  speed crystal oscillator  Pow er up 

27 

PLLI2SSTB 

PLLI2S  clock stabilization  flag 

Set by hardw are to indicate if the PLLI2S  output clock is stable  and ready for use. 

0: PLLI2S  is not stable 

1: PLLI2S  is stable

 

26 

PLLI2SEN 

PLLI2S  enable 

Set and reset by softw are. Reset by hardw are w hen entering Deep-sleep  or Standby  

mode.   

0: PLLI2S  disable   

1: PLLI2S  enable   

25 

PLLSTB 

PLL  clock stabilization  flag 

Set by hardw are to indicate if the  PLL  output  clock is stable and ready for use. 

0: PLL  is not stable 

1: PLL  is stable

 

24 

PLLEN 

PLL  enable 

Set and  reset by softw are. This bit  cannot be reset if the PLL  clock is used as the 

system clock. Reset by hardw are w hen entering  Deep-sleep  or Standby mode.   

0: PLL  disable   

1: PLL  enbale   

23

 

PLLDIGSTB 

PLLDIG  Clock  Stabilization  Flag 

Set by hardw are to indicate if the PLLDIG  output  clock is stable and ready for use. 

0: PLLDIG  is not stable 

1: PLLDIG  is stable 

22 

RFCKMEN 

HXTAL  Clock  Monitor  Enable,  Check  RF  XTAL   

0: Disable  the High  speed crystal oscillator (HXTAL)  clock monitor   

1: Enable  the High  speed crystal oscillator  (HXTAL) clock monitor  

21 

PLLDIGEN 

PLLDIG  enable,  This  bit cannot be reset if the PLLDIG  clock is used as the system 

clock 

Set and reset by softw are.  

0: PLLDIG  disable   

1: PLLDIG  enable   

20 

PLLDIGPU 

PLLDIG  pow er up, This bit cannot be reset if the PLLDIG  clock is used as the system 

clock. 

Set and reset by softw are. Reset by hardw are w hen entering Deep-sleep  or Standby  

mode.   

0: PLLDIG  pow er dow n.   

1: PLLDIG  pow er up.   

19 

CKMEN 

HXTAL  clock monitor  enable   

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

Abus TVVR36500 User Manual preview
TVVR36500
Brand: Abus Pages: 60
Raidon SAFETank Series User Manual preview
SAFETank Series
Brand: Raidon Pages: 49
Dialogic DM/IP601-CPCI-100BT Quick Install Card preview
DM/IP601-CPCI-100BT
Brand: Dialogic Pages: 2
LGC wireless InterReach Fusion SingleStar Installation And Operation Manual preview
InterReach Fusion SingleStar
Brand: LGC wireless Pages: 154
SIIG ID-P20211-S1 Quick Installation Manual preview
ID-P20211-S1
Brand: SIIG Pages: 20
H3C NIC-FC730i-Mb-2-32G Manual preview
NIC-FC730i-Mb-2-32G
Brand: H3C Pages: 37
NC-link NC-AP111 User Manual preview
NC-AP111
Brand: NC-link Pages: 20
B-G Instruments DataPlot CB1224 Manual preview
DataPlot CB1224
Brand: B-G Instruments Pages: 4
Ubiquiti airMAX NanoBridge M NBM3 Quick Start Manual preview
airMAX NanoBridge M NBM3
Brand: Ubiquiti Pages: 24
Tripp Lite SmartRack SR25UBEXP Specifications preview
SmartRack SR25UBEXP
Brand: Tripp Lite Pages: 4
IEI Technology PE-6S-R40 User Manual preview
PE-6S-R40
Brand: IEI Technology Pages: 4
IBM 2078-4F4 Quick Installation Manual preview
2078-4F4
Brand: IBM Pages: 130
M-system M5XSBS Instruction Manual preview
M5XSBS
Brand: M-system Pages: 4
uneron eSOM3735z Quick Start Manual preview
eSOM3735z
Brand: uneron Pages: 13
Renesas Protection Board R0E330850ACBP0 User Manual preview
Protection Board R0E330850ACBP0
Brand: Renesas Pages: 8
WTI NPS-16HD20-1 User Manual preview
NPS-16HD20-1
Brand: WTI Pages: 178
Adaptec ASR-3085 Important Information About Issues And Errata preview
ASR-3085
Brand: Adaptec Pages: 3
Ecolab EcoJet EcoStar 1500 Installation & Operation Manual preview
EcoJet EcoStar 1500
Brand: Ecolab Pages: 80

Brands by name

Popular brands

Load more brands