manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

670 

 

 

20. 

Serial peripheral interface/Inter-IC sound (SPI/I2S) 

20.1. 

Overview 

The SPI/I2S module can communicate with external devices using the SPI protocol or the I2S 

audio protocol. 

The  serial  peripheral  interface  (SPI)  provides  a  SPI  protocol  of  data  transmission and 

reception function in  master or  slave  mode. Both  full-duplex and  simplex communication 

modes are supported, with hardware CRC calculation and checking. Quad-SPI master mode 

is only supported in SPI0. 

The inter-IC sound (I2S) supports four audio standards: I2S Phillips standard, MSB justified 

standard, LSB justified standard, and PCM standard. I2S works at either master or slave 

mode  for  transmission  and  reception.  (By  using  I2S1_ADD  module,  full  duplex  mode

 

communication is realized in I2S1.)

 

 

20.2. 

Characteristics 

20.2.1. 

SPI characteristics 

 

Master or slave operation with full-duplex or simplex mode. 

 

Separate transmit and receive buffer, 16 bits wide. 

 

Data frame size can be 8 or 16 bits. 

 

Bit order can be LSB or MSB. 

 

Software and hardware NSS management. 

 

Hardware CRC calculation, transmission and checking. 

 

Transmission and reception using DMA. 

 

SPI TI mode supported. 

 

Quad-SPI configuration available in master mode (only in SPI0). 

20.2.2. 

I2S characteristics 

 

Master or slave operation for transmission/reception. 

 

Master or slave operation with full-duplex mode(only in I2S1) 

 

Four I2S standards supported: Phillips, MSB justified, LSB justified and PCM standard. 

 

Data length can be 16 bits, 24 bits or 32 bits. 

 

Channel length can be 16 bits or 32 bits. 

 

Transmission and reception using a 16 bits wide buffer. 

 

Audio sample frequency can be 8 kHz to 192 kHz using I2S clock divider. 

 

Programmable idle state clock polarity. 

 

Master clock (MCK) can be output. 

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

ABB i-bus KNX IPR/S 3.5.1 Product Manual preview
i-bus KNX IPR/S 3.5.1
Brand: ABB Pages: 44
Parker H Series Installation & Service Instructions Manual preview
H Series
Brand: Parker Pages: 344
Lochinvar Armor 101 Series Instructions Manual preview
Armor 101 Series
Brand: Lochinvar Pages: 28
Lochinvar Armor 101 Series Service Manual preview
Armor 101 Series
Brand: Lochinvar Pages: 44
Supero AOC-SIMLC User Manual preview
AOC-SIMLC
Brand: Supero Pages: 68
Klark Teknik DN9650 Operator'S Manual preview
DN9650
Brand: Klark Teknik Pages: 50
ekwb EK-FC Installation Manual preview
EK-FC
Brand: ekwb Pages: 2
IBM EtherLink XL User Manual preview
EtherLink XL
Brand: IBM Pages: 72
OPTO 22 PCI-AC48 User Manual preview
PCI-AC48
Brand: OPTO 22 Pages: 28
Omega Engineering BNC-08DI, BNC-16DI, BNC-16SE User Manual preview
BNC-08DI, BNC-16DI, BNC-16SE
Brand: Omega Engineering Pages: 25
NEC LED-VP1 User Manual preview
LED-VP1
Brand: NEC Pages: 17
StarTech.com SATSASTRX25 Manual preview
SATSASTRX25
Brand: StarTech.com Pages: 7
NEC N8151-106 Startup Manual preview
N8151-106
Brand: NEC Pages: 6
NEC NEC Express5800 Series Specifications preview
NEC Express5800 Series
Brand: NEC Pages: 2
NEC N8151-121 User Manual preview
N8151-121
Brand: NEC Pages: 4
NEC N8151-103 Startup Manual preview
N8151-103
Brand: NEC Pages: 6
NEC N8146-91 User Manual preview
N8146-91
Brand: NEC Pages: 12
NEC N8151-78A Startup Manual preview
N8151-78A
Brand: NEC Pages: 4

Brands by name

Popular brands

Load more brands