manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

119 

 

 

4. 

Instruction cache (ICACHE) 

4.1. 

Introduction 

The  instruction cache (ICACHE)  is based on C-AHB  code bus of Cortex-M33  processor. 

It is necessary to improve  performance  in fetching  instruction and data from  both internal 

and  external memories. 

4.2. 

Characteristics 

 

•

  Support  32KB cache with 2 ways, 1024  cache lines per  way and  16B per cache line   

•

  Support  fetch address without any wait state if  cache hit  

•

  ICACHE interface  support two 32-bit slave ports and two 32-bit master ports. One slave 

port is execution port, the other one  is for  registers access. Master 0 port  outputs to fast 

bus, while  master 1 port outputs to slow bus. 

•

  Cache  access support hit-under-miss and  paired  master access feature 

•

  Support  memory address remap 

•

  Support  pLRU  replacement  policy and  critical-word-first  refill policy. 

•

  Support  remap  region  AHB transaction burst type configuration.  

•

  Support  two  performance  counters: 32-bit  hit monitor  counter  and16-bit  miss monitor 

counter. 

•

  Operation  management:  Cache  invalidate  and  optional interrupt  handle.   

•

  Support  TrustZone  security and  configure  registers to be protected at system level. 

4.3. 

Function overview 

The purpose  of ICACHE  is to cache fetched instruction and data, only for read transaction, 

not  for  write  transaction.  Considering  error  management,  in  case  of  detecting  an 

unexpected  cacheable write access, set an error  flag  and  trigger optionally  an interrupt. 

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

H3C S5120V3-EI Series Manual preview
S5120V3-EI Series
Brand: H3C Pages: 54
Ublox LENA-R8 Series System Integration Manual preview
LENA-R8 Series
Brand: Ublox Pages: 116
Renesas F-ZTAT H8/3048 Series User Manual preview
F-ZTAT H8/3048 Series
Brand: Renesas Pages: 34
Analog Devices ADAU1961 Manual preview
ADAU1961
Brand: Analog Devices Pages: 76
A4Tech RG-71M User Manual preview
RG-71M
Brand: A4Tech Pages: 7
RAIDAGE DAGE312UTL-NAS User Manual preview
DAGE312UTL-NAS
Brand: RAIDAGE Pages: 60
Qlogic QLE7xxx Series Quick Start Manual preview
QLE7xxx Series
Brand: Qlogic Pages: 8
ZALMAN ZM-RF1 User Manual preview
ZM-RF1
Brand: ZALMAN Pages: 5
4gon RouterBOARD 411R Quick Start Manual preview
RouterBOARD 411R
Brand: 4gon Pages: 2
EMS 2000 IDU Series User Manual preview
2000 IDU Series
Brand: EMS Pages: 52
SafeHome NVR903 Manual preview
NVR903
Brand: SafeHome Pages: 24
National Instruments PXI Terminal Block NI TB-2709 Installation Manual preview
PXI Terminal Block NI TB-2709
Brand: National Instruments Pages: 12
Sony Ericsson GC83 Specification preview
GC83
Brand: Sony Ericsson Pages: 2
Hanwha Techwin Wisenet XRN-6410RB2-24TB User Manual preview
Wisenet XRN-6410RB2-24TB
Brand: Hanwha Techwin Pages: 124
Radica Games DAVID-II 716 Operating And Maintenance Instruction Manual preview
DAVID-II 716
Brand: Radica Games Pages: 40
Airvana ipBTS C30 Installation And Commissioning Manual preview
ipBTS C30
Brand: Airvana Pages: 90
Renesas HD74HCT1G04 Datasheet preview
HD74HCT1G04
Brand: Renesas Pages: 8
CyberResearch CPBF PMX-233 User Manual preview
CPBF PMX-233
Brand: CyberResearch Pages: 59

Brands by name

Popular brands

Load more brands