manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

864 

 

 

7 

PSP 

Port  suspend 

Application  sets this bit to put port into  suspend state. When  this bit is set the port 

stops sending SOF  tokens.  This bit  can only be  cleared by the  follow ing operations : 

PRST  bit in this register is set by application 

PREM  bit in this register  is set 

A remote  w akeup signal is detected   

A device disconnect  is detected 

0: Port is not in suspend  state 

1: Port is in suspend  state 

6 

PREM 

Port  resume 

Application  sets this  bit  to  start a resume  signal  on  USB  port.  Application  should 

clear this bit w hen it w ants to stop the resume  signal. 

0: No resume  driven 

1: Resume  driven 

5:4 

Reserved 

Must  be kept  at reset value 

3 

PEDC 

Port  enable/disable  change 

Set by the core w hen the status of the Port  enable  bit 2 in this register changes. 

2 

PE 

Port  Enable 

This bit is automatically  set by USBFS  after a USB  reset signal finishes and cannot 

be set by softw are. 

This bit is cleared by the follow ing events: 

A disconnect condition 

Softw are clearing this bit 

0: Port disabled 

1: Port enabled 

1 

PCD 

Port  connect detected 

Set  by USBFS  w hen a device  connection  is  detected.  This  bit  can  be cleared  by 

w riting 1 to this bit. 

0 

PCST 

Port  connect status 

0: Device is not connected to the port 

1: Device is connected to the port 

Host  channel-x  control  register  (USBFS_HCHxCTL)  (x  =  0..7  where  x  = 

channel_number) 

Address offset:  (channel_number × 0x20) 

Reset value: 0x0000 0000 

This register has to be accessed by word (32-bit) 

 

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

D-Link ShareCenter DNS-320L Datasheet preview
ShareCenter DNS-320L
Brand: D-Link Pages: 4
VAF instruments 667 Instructions For Installation, Operation And Maintenance preview
667
Brand: VAF instruments Pages: 56
Palm M505 Setting Up preview
M505
Brand: Palm Pages: 4
Hama FireWire Combo Instructions Manual preview
FireWire Combo
Brand: Hama Pages: 8
Lutron Electronics Smart Bridge Quick Start Manual preview
Smart Bridge
Brand: Lutron Electronics Pages: 4
Supero SAS 846 TQ User Manual preview
SAS 846 TQ
Brand: Supero Pages: 16
Omron F3SP-U3P-TGR User Manual preview
F3SP-U3P-TGR
Brand: Omron Pages: 29
Net Optics Phantom HD Quick Install Manual preview
Phantom HD
Brand: Net Optics Pages: 2
Grizzly PSJ-VZ58 gen3 OEM User Manual preview
PSJ-VZ58 gen3 OEM
Brand: Grizzly Pages: 12
NXP Semiconductors i.MX 8M Mini LPDDR4 EVK User Manual preview
i.MX 8M Mini LPDDR4 EVK
Brand: NXP Semiconductors Pages: 20
ADC 150-204-100-03 User Manual preview
150-204-100-03
Brand: ADC Pages: 29
Dahua DHI-NVR5208-4KS2 User Manual preview
DHI-NVR5208-4KS2
Brand: Dahua Pages: 361
Dahua NVR5208-EI User Manual preview
NVR5208-EI
Brand: Dahua Pages: 489
Crestron UC-CAM-UPGRD-300 Quick Start preview
UC-CAM-UPGRD-300
Brand: Crestron Pages: 2
ASROCK IMB-X1314 User Manual preview
IMB-X1314
Brand: ASROCK Pages: 45
Fujitsu F2MC-16L Series User Manual preview
F2MC-16L Series
Brand: Fujitsu Pages: 68
Spirent TestCenter Getting Started With preview
TestCenter
Brand: Spirent Pages: 86
NuAire MEV-ECO-H Installation Manual preview
MEV-ECO-H
Brand: NuAire Pages: 8

Brands by name

Popular brands

Load more brands