manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

195 

 

 

9:8 

RTCSRC[1:0] 

RTC  clock entry selection 

Set  and  reset  by softw are to control  the  RTC  clock  source. Once  the  RTC  clock 

source  has  been  selected,  it  cannot  be  changed  anymore  unless  the  Backup 

domain  is reset. 

00: No clock selected 

01: CK_LXTAL  selected as RTC  source clock 

10: CK_IRC32K  selected as RTC  source clock 

11: (CK_HXTAL  / RTCDIV)  selected as RTC  source clock, please refer to RTCDIV  

bits in RCU_CFG0  register. 

7:5 

Reserved 

Must  be kept  at reset value. 

4:3 

LXTALDRI[1:0] 

LXTAL  drive capability 

Set and reset by softw are. Backup domain  reset resets this value. 

00: low er driving capability   

01: high driving capability   

10: higher driving capability 

11: highest driving capability  (reset value) 

Note:  The  LXTALDRI  is not in bypass mode. 

2 

LXTALBPS 

LXTAL  bypass mode  enable 

Set and reset by softw are. 

0: Disable  the LXTAL Bypass mode   

1: Enable  the LXTAL  Bypass mode 

1 

LXTALSTB 

Low  speed crystal oscillator  stabilization  flag 

Set by hardw are to indicate if the LXTAL output  clock is stable and ready for use.   

0: LXTAL is not stable 

1: LXTAL is stable 

0 

LXTALEN 

LXTAL  enable 

Set and reset by softw are. 

0: Disable  LXTAL 

1: Enable  LXTAL 

6.5.21. 

Reset source/clock  register (RCU_RSTSCK) 

Address offset: 0x74 

Reset value: 0x0C00 0000, all reset flags reset by power reset only, RSTFC/IRC32KEN 

reset by system reset. 

This register can be accessed by byte(8-bit), half-word(16-bit) and word(32-bit)  

31 

30 

29 

28 

27 

26 

25 

24 

23 

22 

21 

20 

19 

18 

17 

16 

LP 

RSTF 

WWDGT

RSTF 

FWDGT 

RSTF 

SW 

RSTF 

POR 

RSTF 

EP 

RSTF 

OBLRST

F 

RSTFC 

Reserved 

r 

r 

r 

r 

r 

r 

r 

rw 

 

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

3Com 3C3FE574BT Quick Start Manual preview
3C3FE574BT
Brand: 3Com Pages: 8
dbx ProVocal Specifications preview
ProVocal
Brand: dbx Pages: 2
Lattice Semiconductor ECP5 Versa Quick Start Manual preview
ECP5 Versa
Brand: Lattice Semiconductor Pages: 15
Ruckus Wireless ZoneFlex 7731 Getting Started Manual preview
ZoneFlex 7731
Brand: Ruckus Wireless Pages: 56
Renesas RSKH836079 Quick Start Manual preview
RSKH836079
Brand: Renesas Pages: 6
VCS VideoJet 100 Manual preview
VideoJet 100
Brand: VCS Pages: 118
Hama 00039747 Operating Instruction preview
00039747
Brand: Hama Pages: 6
Blackmagicdesign Teranex 2D Processor Installation And Operation Manual preview
Teranex 2D Processor
Brand: Blackmagicdesign Pages: 969
Moxa Technologies PT-7710 Series Hardware Installation Manual preview
PT-7710 Series
Brand: Moxa Technologies Pages: 2
NXP Semiconductors UM10301 PCA8565 User Manual preview
UM10301 PCA8565
Brand: NXP Semiconductors Pages: 54
ebm-papst R3G560-AH02-03 Operating Instructions Manual preview
R3G560-AH02-03
Brand: ebm-papst Pages: 13
Xantech IR-X10 Installation Instructions Manual preview
IR-X10
Brand: Xantech Pages: 16
IEI Technology Mustang-M2AE-MX1 User Manual preview
Mustang-M2AE-MX1
Brand: IEI Technology Pages: 58
Renesas PROM Programming Adapters PCA7438F-64A User Manual preview
PROM Programming Adapters PCA7438F-64A
Brand: Renesas Pages: 18
Fast FV3000-W2K Instruction Manual preview
FV3000-W2K
Brand: Fast Pages: 66
Thecus 1U4600 User Manual preview
1U4600
Brand: Thecus Pages: 148
LevelOne GSW-0508 User Manual preview
GSW-0508
Brand: LevelOne Pages: 10
SET 89299 Technical Description preview
89299
Brand: SET Pages: 38

Brands by name

Popular brands

Load more brands