manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

87 

 

 

register. This bit can be set by softw are. 

6 

START 

Send  erase command  to FMC 

This bit is set by softw are to send erase command  to FMC.   

This bit is cleared by hardw are w hen the BUSY  bit is cleared. 

5:3 

Reserved 

Must  be kept  at reset value. 

2 

MER 

Main  Flash mass erase command  bit 

This bit is set or cleared by softw are 

0: no effect 

1: main  Flash  mass erase command 

1 

PER 

Main  Flash page erase command  bit 

This bit is set or clear by softw are 

0: no effect 

1: main  Flash  page erase command 

0 

PG 

Main  Flash program  command  bit 

This bit is set or clear by softw are 

0: no effect 

1: main  Flash  program  command 

Note:

 

This register should be reset after the corresponding Flash operation completed.  

2.5.5. 

Address  register (FMC_ADDR) 

Address offset: 0x14 

Reset value: 0x0000 0000 

This register is non-secure. Protected against non-provileged access when FMC_PRIV=1. 

This register has to be accessed by word (32-bit). 

31 

30 

29 

28 

27 

26 

25 

24 

23 

22 

21 

20 

19 

18 

17 

16 

ADDR[31:16] 

W 

15 

14 

13 

12 

11 

10 

9 

8 

7 

6 

5 

4 

3 

2 

1 

0 

ADDR[15:0] 

W 

 

Bits 

Fields 

Descriptions  

31:0 

ADDR[31:0] 

Flash  erase/program  command  address bits  

These bits are configured by softw are. 

ADDR  bits are the address of Flash  to be erased/programmed. 

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

Keithley 7707 User Manual preview
7707
Brand: Keithley Pages: 59
Balluff BIC 1I12-P2A25-M30MI1-BPX05-110 User Manual preview
BIC 1I12-P2A25-M30MI1-BPX05-110
Brand: Balluff Pages: 12
Grizzly PSJ-M3 GEN2 User Manual preview
PSJ-M3 GEN2
Brand: Grizzly Pages: 9
e-con Systems See3CAM 30 Z10X Application User'S Manual preview
See3CAM 30 Z10X
Brand: e-con Systems Pages: 14
S&P Turbo-3000 Operating Instructions preview
Turbo-3000
Brand: S&P Pages: 3
ProSoft MVI46-PDPS User Manual preview
MVI46-PDPS
Brand: ProSoft Pages: 53
LevelOne GSW-0508 User Manual preview
GSW-0508
Brand: LevelOne Pages: 10
SET 89299 Technical Description preview
89299
Brand: SET Pages: 38
Link electronics Analog Pulse Generator 812-OP/H Specification Sheet preview
Analog Pulse Generator 812-OP/H
Brand: Link electronics Pages: 2
TP-Link VIGI Quick Start Manual preview
VIGI
Brand: TP-Link Pages: 2
Curtiss-Wright GTS/DEC/006 Instructions Manual preview
GTS/DEC/006
Brand: Curtiss-Wright Pages: 10
MSI MEG CORELIQUID S280 User Manual preview
MEG CORELIQUID S280
Brand: MSI Pages: 21
MikroTik CCR2004-16G-2S+ Quick Start Manual preview
CCR2004-16G-2S+
Brand: MikroTik Pages: 5
Abocom LA100 Quick Installation Manual preview
LA100
Brand: Abocom Pages: 20
Talkswitch TALKSWITCH 24-CA Quick Manual preview
TALKSWITCH 24-CA
Brand: Talkswitch Pages: 9
Trust ISDN 128 User Manual preview
ISDN 128
Brand: Trust Pages: 49
Edge-Core SDW101 Quick Start Manual preview
SDW101
Brand: Edge-Core Pages: 5
ST X-NUCLEO-LED12A1 User Manual preview
X-NUCLEO-LED12A1
Brand: ST Pages: 17

Brands by name

Popular brands

Load more brands