manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

42 

 

 

SRAMs 

All SRAMs  are secure after reset. TZBMPC  (TrustZone  block-based 

memory  protection controller) is secure.   

External  memories 

QSPI_FLASH  and SQPI_PSRA M  banks are secure after reset. 

Peripherals 

Securable  peripherals  are  non-secure  after  reset.  TrustZone-aw are 

peripherals  are  non-secure  after  reset  (except  GPIOA,  GPIOB  and 

GPIOC).  Their secure configuration registers are secure. Refer to 

Table 

1-3.  Securable peripherals by  TZSPC

 

and 

Table  1-4.  TrustZone-

aware  peripherals

  for  a  list  of  Securable  and  TrustZone-aw are 

peripherals. 

GPIO 

All GPIO  are secure after reset 

Interrupts 

NVIC:  All interrupts  are secure after reset. NVIC  is banked  for secure 

and non-secure state. 

TZIAC:  All illegal  access interrupts are disabled  after reset. 

1.3.2. 

Peripheral classification 

When the TrustZone security is active, a peripheral can be securable, secure, non-secure or 

TrustZone-aware type. 

For securable peripherals by TZSPC (TrustZone security controller), 

the SEC security bit corresponding to this peripheral is set in the TZSPC_SAM_CFGx register. 
For securable peripherals by TZSPC (TrustZone security controller), the SEC security bit 
corresponding to this peripheral is set in the TZSPC_SAM_CFGx register. TZIAC, TZBMPCx 

and EFUSE are always secure and AHB masters (WI-FI) always

 non-secure. For TrustZone-

aware peripherals, a security feature of this peripheral is enabled through its dedicated bits. 

Table 1-3. Securable peripherals by TZSPC

 

and 

Table 1-4. TrustZone-aware peripherals

 

summarize the list of securable and TrustZone-aware peripherals within the system. 

Table 1-3. Securable peripherals by TZSPC 

BUS 

Peripheral 

AHB1 

CRC 

USBFS 

Wi-Fi

 

ICACHE 

QSPI_FLASH( REG) 

SQPI_PSRA M( REG) 

TSI 

AHB2 

DCI 

CAU 

HAU 

TRNG 

PKCAU 

AHB3 

SQPI_PSRA M 

APB1 

TIMER1 

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

NEC Univerge SV8100 System Configuration Manual preview
Univerge SV8100
Brand: NEC Pages: 44
ICP DAS USA I-7532M-FD User Manual preview
I-7532M-FD
Brand: ICP DAS USA Pages: 48
ICP DAS USA WF-2572 User Manual preview
WF-2572
Brand: ICP DAS USA Pages: 24
Q-See QC814 Specifications preview
QC814
Brand: Q-See Pages: 2
Analog Devices Linear SCP-LT8362-S-EVALZ Demo Manual preview
Linear SCP-LT8362-S-EVALZ
Brand: Analog Devices Pages: 8
Orban OPTIMOD 6300 Operating Manual preview
OPTIMOD 6300
Brand: Orban Pages: 255
MEDIATEK MT6252 Design Manual preview
MT6252
Brand: MEDIATEK Pages: 166
Aqua Computer Aquaduct 240 eco Operating And Assembly Manual preview
Aquaduct 240 eco
Brand: Aqua Computer Pages: 20
2N Telekomunikace ATEUS STARGATE User Manual preview
ATEUS STARGATE
Brand: 2N Telekomunikace Pages: 67
Antec KÜHLER H2O 920 Software Manual preview
KÜHLER H2O 920
Brand: Antec Pages: 6
Knowles IA611 Xplained Pro User Manual preview
IA611 Xplained Pro
Brand: Knowles Pages: 14
Intel SRCU31L Quick Start Manual preview
SRCU31L
Brand: Intel Pages: 20
Intel G6950 Documentation Update preview
G6950
Brand: Intel Pages: 51
ZALMAN OPTIMA II CNPS10X User Manual preview
OPTIMA II CNPS10X
Brand: ZALMAN Pages: 20
Renesas PCA7755D User Manual preview
PCA7755D
Brand: Renesas Pages: 6
Quantum MC300 Prism User Manual preview
MC300 Prism
Brand: Quantum Pages: 140
Airaya AI108-1-050 Quick Install Manual preview
AI108-1-050
Brand: Airaya Pages: 28
Extron electronics IPL Pro Series User Manual preview
IPL Pro Series
Brand: Extron electronics Pages: 10

Brands by name

Popular brands

Load more brands