manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

95 

 

 

when OBRLD is set or system reset.)  

This register can only be written if OBWEN bit is set. This register is non-secure. It can be 

read  and  written  by  both  secure and  non-secure access. This register  can  be  protected 

against non-privileged access when FMC_PRIV=1. 

This register has to be accessed by word (32-bit). 

31 

30 

29 

28 

27 

26 

25 

24 

23 

22 

21 

20 

19 

18 

17 

16 

Reserved 

WRP0_EPAGE[9:0] 

 

rw 

15 

14 

13 

12 

11 

10 

9 

8 

7 

6 

5 

4 

3 

2 

1 

0 

Reserved 

WRP0_SPAGE[9:0] 

 

rw 

 

Bits 

Fields 

Descriptions  

31:26 

Reserved 

Must  be kept  at reset value. 

25:16 

WRP0_EPAGE[9:0] 

End  page of w rite protection  area 0 

15:10 

Reserved 

Must  be kept  at reset value. 

9:0 

WRP0_SPAGE[9:0] 

Start page of w rite protection area 0   

2.5.16. 

Secure mark  configuration  register 1 (FMC_SECMCFG1) 

Address offset: 0x54 

Reset value: 0x0000 03FF / 0xXXXX  XXXX  (When there are option bytes, register bits 0 to 

31 are  loaded with values from  Flash memory when OBRLD is set or  system reset. When 

there no option bytes, the reset value is kept at 0x0000 03FF.) 

This register can not be written if OBWEN bit is set. 

This register is secure when TZEN = 1. It can be read and written only by secure access or 

TZEN = 0. A non-secure read/write access is RAZ/WI. This register can be protected against 

non-privileged access when FMC_PRIV = 1. 

This register has to be accessed by word (32-bit). 

31 

30 

29 

28 

27 

26 

25 

24 

23 

22 

21 

20 

19 

18 

17 

16 

Reserved 

SECM1_EPAGE[9:0] 

 

rw 

15 

14 

13 

12 

11 

10 

9 

8 

7 

6 

5 

4 

3 

2 

1 

0 

Reserved 

SECM1_SPAGE[9:0] 

 

rw 

 

Bits 

Fields 

Descriptions  

31:26 

Reserved 

Must  be kept  at reset value. 

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

EAW MX250 Owner'S Manual preview
MX250
Brand: EAW Pages: 10
LaCie d2 Network 2 Quick Install Manual preview
d2 Network 2
Brand: LaCie Pages: 44
LaCie LaCie Ethernet Disk Datasheet preview
LaCie Ethernet Disk
Brand: LaCie Pages: 2
LaCie SATA II ExpressCard 34 Datasheet preview
SATA II ExpressCard 34
Brand: LaCie Pages: 2
LaCie 12big Rack Fibre 8 Quick Install Manual preview
12big Rack Fibre 8
Brand: LaCie Pages: 9
TFortis Teleport-1 Configuration Manual preview
Teleport-1
Brand: TFortis Pages: 86
Jetter JetWeb JX2-PR0FI1 Operator'S Manual preview
JetWeb JX2-PR0FI1
Brand: Jetter Pages: 67
Internet Security Systems Proventia A1204 User Manual preview
Proventia A1204
Brand: Internet Security Systems Pages: 42
Datasat DDR-16 AES67 Installation And Operating Manual preview
DDR-16 AES67
Brand: Datasat Pages: 24
Dust Networks SmartMesh IA-510 D2511 Manager'S Manual preview
SmartMesh IA-510 D2511
Brand: Dust Networks Pages: 30
Moxa Technologies PT-7710 Series Hardware Installation Manual preview
PT-7710 Series
Brand: Moxa Technologies Pages: 2
IDT Digital Encoder Plus User Manual preview
Digital Encoder Plus
Brand: IDT Pages: 98
Lanner NCA-1040 User Manual preview
NCA-1040
Brand: Lanner Pages: 59
Alarm NX-208E Installation Manual preview
NX-208E
Brand: Alarm Pages: 5
Primera Disc Publisher XR Installation Instructions preview
Disc Publisher XR
Brand: Primera Pages: 2
JETWAY I848ASR1A User Manual preview
I848ASR1A
Brand: JETWAY Pages: 47
Gundermann VIDEOWALL LEDWALL Optimizer HQ P2 Manual preview
LEDWALL Optimizer HQ P2
Brand: Gundermann VIDEOWALL Pages: 12
Raven RFMOW V2 User Manual preview
RFMOW V2
Brand: Raven Pages: 33

Brands by name

Popular brands

Load more brands