manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

465 

 

 

TIMERx_CTL1 register as soon as POEN is 0. If IOS is 0 then the timer releases the enable 
output else the enable output remains high. The complementary outputs are first put in reset 
state, and then the dead-time generator is reactivated in order to drive the outputs with the 
level programmed in the ISOx and ISOxN bits after a dead-time.  

When a break occurs, the BRKIF bit in the TIMERx_INTF register is set. If BRKIE is 1, an 
interrupt generated.  

Figure 17-19. Output behavior of the channel in response to a break (the break high 
active) 

OxCPRE

CHx_O

CHx_ON

BRKIN

CHx_O

CHx_ON

CHx_O

CHx_ON

= ISOx

= ISOxN

= ISOx

= ISOxN

CHxEN: 1  CHxNEN: 1
CHxP   : 0  CHxNP  : 0
ISOx = ~ISOxN 

CHxEN: 1  CHxNEN: 0
CHxP: 0    CHxNP   : 0
ISOx = ~ISOxN 

CHxEN: 1  CHxNEN: 0
CHxP  : 0   CHxNP  : 0
ISOx = ISOxN 

 

Quadrature decoder 

The quadrature decoder function uses two quadrature inputs CI0 and CI1 derived from the 
TIMERx_CH0 and TIMERx_CH1 pins respectively to interact with each other to generate the 
counter value. Setting SMC=0x01, 0x02, or 0x03 to select that the counting direction of timer 
is determined only by the CI0, only by the CI1, or by the CI0 and the CI1. The DIR bit is 
modified  by  hardware  automatically  during  the  voltage  level  change  of  each  direction 
selection source. The mechanism of changing the counter direction is shown in 

Table 17-3. 

Counting direction versus encoder signals

. The quadrature decoder can be regarded as 

an external clock with a direction selection. This means that the counter counts continuously 
from 0 to the counter-reload value. Therefore, users must configure the TIMERx_CAR register 
before the counter starts to count. 

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

Raritan DOMINION SX - Quick Setup Manual preview
DOMINION SX -
Brand: Raritan Pages: 4
Alcad ZA-431 Quick Start Manual preview
ZA-431
Brand: Alcad Pages: 6
NXP Semiconductors MIMXRT1160 Hardware Development Manual preview
MIMXRT1160
Brand: NXP Semiconductors Pages: 24
KEMP Technologies LoadMaster 1500 Installation And Configuration Manual preview
LoadMaster 1500
Brand: KEMP Technologies Pages: 71
SUNRICH TECHNOLOGY C-330 User Manual preview
C-330
Brand: SUNRICH TECHNOLOGY Pages: 5
Xilica Audio Design XP 4080 User Manual preview
XP 4080
Brand: Xilica Audio Design Pages: 30
Kontron CPS3003-SA User Manual preview
CPS3003-SA
Brand: Kontron Pages: 19
Microchip Technology DM240316 Quick Start Manual preview
DM240316
Brand: Microchip Technology Pages: 9
Billion BiPAC 5200S RC Series User Manual preview
BiPAC 5200S RC Series
Brand: Billion Pages: 79
Renesas PROM Programming Adapters PCA7438F-64A User Manual preview
PROM Programming Adapters PCA7438F-64A
Brand: Renesas Pages: 18
EVGA inDtube Instructions preview
inDtube
Brand: EVGA Pages: 3
Lanpro LP-F22 Series Assembling Instructions preview
LP-F22 Series
Brand: Lanpro Pages: 3
Lefroy Brooks M1-5100 Installation, Operating, & Maintenance Instructions preview
M1-5100
Brand: Lefroy Brooks Pages: 10
SIIG ExpressCard 11-in-1 Reader/Writer Quick Installation Manual preview
ExpressCard 11-in-1 Reader/Writer
Brand: SIIG Pages: 8
H3C SecPath L5030 Installation Manual preview
SecPath L5030
Brand: H3C Pages: 62
ZALMAN CNPS2005-Plus User Manual preview
CNPS2005-Plus
Brand: ZALMAN Pages: 6
Proxim Lynx.GX 16T Installation And Management Manual preview
Lynx.GX 16T
Brand: Proxim Pages: 45
Multitech MultiModem ISIHP-2S User Manual preview
MultiModem ISIHP-2S
Brand: Multitech Pages: 155

Brands by name

Popular brands

Load more brands