manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

766 

 

 

SDIO_FIFO register address. Configure DMA1 _Channel3 or DMA1 _Channel6 Peripheral4 
control register (memory with increment transfer,  peripheral  with not  increment transfer, 
peripheral and memory data size is word size). Program the incremental burst transfer to 4 
on peripheral side in DMA1 _Channel 3 or DMA1 _Channel 6 Peripheral4. 

5. Write block to card as follows: 

Write the data size in bytes in the SDIO_DATALEN register. Write the block size in bytes 
(BLKSZ) in the SDIO_DATACTL register; the host sends data in blocks of size BLKSZ each. 
Program SDIO_CMDAGMT register with the data address, where data should be written. 
Program the SDIO command control register (SDIO_CMDCTL): CMDIDX with 24, CMDRESP 
with 1  (SDIO  card host waits for  a  short response); CSMEN with 

‘

1

’

  (enable to  send a 

command). Other fields are their reset value. 

When the CMDRECV flag is set, program the SDIO data control register (SDIO_DATACTL): 
DATAEN with 1 (enable to send data); DATADIR with 0 (from controller to card); TRANSMOD 
with 0 (block data transfer); DMAEN with 1 (DMA enabled); BLKSZ with 0x9 (512 bytes). 
Other bits don

’

t care. 

Wait for DTBLKEND flag is set. Check that no channels are still enabled by polling the DMA 
Interrupt Flag register. 

It consists the following subunits: 

Register unit 

The  register unit which contains all system registers generates the signals to control the 
communication between the controller and card. 

Data FIFO 

The data FIFO unit has a data buffer, uses as transmit and receive FIFO. The FIFO contains 
a 32-bit wide, 32-word deep data buffer. The transmit FIFO is used when write data to card 
and TXRUN in SDIO_STAT register is 1. The data to be transferred is written to transmit FIFO 
by APB2 bus, the data unit in SDIO adapter read data from transmit FIFO, and then send the 
data to card. The receive FIFO is used when read data from card and RXRUN in SDIO_STAT 
register is 1. The data to be transferred is read from the card and then write to receive FIFO. 
The data in receive FIFO is read to APB2 bus when needed. This unit also generates FIFO 
flags in SDIO_STAT registers. 

23.5. 

Card functional description 

23.5.1. 

Card registers 

Within the card interface registers are defined: OCR, CID, CSD, EXT_CSD, RCA, DSR and 
SCR. These can be accessed only by corresponding commands. The OCR, CID, CSD and 

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

Laurell WS-650 lite Series Operation Manual preview
WS-650 lite Series
Brand: Laurell Pages: 84
Accuphase AD-60 Instruction Manual preview
AD-60
Brand: Accuphase Pages: 2
ADTRAN ATLAS 550 Manual preview
ATLAS 550
Brand: ADTRAN Pages: 2
Acrosser Technology AMB-VDX3H1 Series Quick Start Manual preview
AMB-VDX3H1 Series
Brand: Acrosser Technology Pages: 4
Profile LS901-E1 Instruction Manual preview
LS901-E1
Brand: Profile Pages: 6
ADC HiGain HLU-231 List 8F Quick Installation preview
HiGain HLU-231 List 8F
Brand: ADC Pages: 7
Genie WONVR216P5 Quick Start Manual preview
WONVR216P5
Brand: Genie Pages: 15
Avaya XM24 Expansion Module Installation Instructions preview
XM24 Expansion Module
Brand: Avaya Pages: 5
Kontron CP3002-RA User Manual preview
CP3002-RA
Brand: Kontron Pages: 98
Promise Technology VTrak J310S Quick Start Manual preview
VTrak J310S
Brand: Promise Technology Pages: 26
H3C SecPath F1070 Manual preview
SecPath F1070
Brand: H3C Pages: 68
ActiveEye K9504L-W Operation Manual preview
K9504L-W
Brand: ActiveEye Pages: 35
Moxa Technologies Smartio CP-104UL Quick Installation Manual preview
Smartio CP-104UL
Brand: Moxa Technologies Pages: 2
Data Translation DT9835 Getting Started Manual preview
DT9835
Brand: Data Translation Pages: 62
One Identity Safeguard for Privileged Sessions 3000 Installation Manual preview
Safeguard for Privileged Sessions 3000
Brand: One Identity Pages: 37
Positron TeleLite 720920 Series Manual preview
TeleLite 720920 Series
Brand: Positron Pages: 21
Siklu EtherHaul 500 Installation Manual preview
EtherHaul 500
Brand: Siklu Pages: 52
Bdcom GP3600-16 Hardware Installation Manual preview
GP3600-16
Brand: Bdcom Pages: 25

Brands by name

Popular brands

Load more brands