manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

1018 

 

 

0: Output clock generation  is disabled  (CKOUT  signal  is set to low  state) 

1~255:  The value of division  for the serial clock output  is C1. 

CKOUTDIV  also defines the threshold  for a clock loss detection.   

This value can only be modified  w hen HPDFEN=0.During  a HPDF  clock cycle after 

HPDFEN=0,  the CKOUT  is set to low  state. 

This bit is only available  in  HPDF_CH0CTL. 

15:14 

DPM[1:0] 

Data  packing  mode  for HPDF_CHx PDI  register 

00: Standard  mode 

01: Interleaved  mode 

10: Dual  mode 

11: Reserved   

For a detailed  introduction  of data encapsulation  mode, please refer to 

Parallel data 

packed mode. 

These bits can be configured only w hen CHEN=0. 

13:12 

CMSD[1:0] 

Channel  x multiplexer  select input data source 

00: Input  data source for channel  x is taken from serial inputs 

01: Reserved   

10: Input  data source for channel  x is taken from internal  HPDF_CHx PDI  register  

11: Reserved   

The  HPDF_CHx PDI  register is w rite protected w hen these bits are reset. 

These bits can be configured only w hen CHEN=0. 

11:9 

Reserved 

Must  be kept  at reset value. 

8 

CHPINSEL 

Channel  inputs pins selection   

0: Channel  inputs select pins of the current channel  x  

1: Channel  inputs select pins of the next channel. 

This bit can be configured only w hen CHEN=0. 

7 

CHEN 

Channel  x enable   

0: Channel  x disabled   

1: Channel  x enabled   

If channel x is enabled,  then serial data w ill be received based on the given channel 

settings. 

6 

CKLEN 

Clock  loss detector enable 

0: Clock  loss detector disabled 

1: Clock  loss detector  enabled 

5 

MMEN 

Malfunction  monitor  enable   

0: malfunction  monitor  is no effect 

1: malfunction  monitor  is effect 

4 

Reserved 

Must  be kept  at reset value. 

3:2 

SPICKSS[1:0] 

SPI  clock source select 

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

Abus TVVR36500 User Manual preview
TVVR36500
Brand: Abus Pages: 60
DBM ACE9600 Operating Manual preview
ACE9600
Brand: DBM Pages: 50
Garmin GND 10 Installation Instructions preview
GND 10
Brand: Garmin Pages: 2
Salusfin SF-930EU User'S Installation Manual preview
SF-930EU
Brand: Salusfin Pages: 6
Accuphase AD-60 Instruction Manual preview
AD-60
Brand: Accuphase Pages: 2
ADTRAN ATLAS 550 Manual preview
ATLAS 550
Brand: ADTRAN Pages: 2
Acrosser Technology AMB-VDX3H1 Series Quick Start Manual preview
AMB-VDX3H1 Series
Brand: Acrosser Technology Pages: 4
TE Connectivity InterReach Fusion ADCP-77-044 Manual preview
InterReach Fusion ADCP-77-044
Brand: TE Connectivity Pages: 236
DAQ system PCIe-FRM13 User Manual preview
PCIe-FRM13
Brand: DAQ system Pages: 41
DAQ system PCIe-SER01 User Manual preview
PCIe-SER01
Brand: DAQ system Pages: 19
WHOOP WHT-25LT Quick Start Manual preview
WHT-25LT
Brand: WHOOP Pages: 26
FS FS-BOX-V3 Quick Start Manual preview
FS-BOX-V3
Brand: FS Pages: 19
RuggedCom RUGGEDMAX WIN7000 Installation Manual preview
RUGGEDMAX WIN7000
Brand: RuggedCom Pages: 42
AYRSTONE AyrMesh IndoorAP Instructions preview
AyrMesh IndoorAP
Brand: AYRSTONE Pages: 2
Lattice Semiconductor iCE40 SPRAM Series Technical Note preview
iCE40 SPRAM Series
Brand: Lattice Semiconductor Pages: 12
Cypress Semiconductor CY7C1410JV18 Specification Sheet preview
CY7C1410JV18
Brand: Cypress Semiconductor Pages: 26
Pilz PNOZ mc3p Operating Instructions Manual preview
PNOZ mc3p
Brand: Pilz Pages: 12
Galileo Quark SoC X1000 Getting Started Manual preview
Quark SoC X1000
Brand: Galileo Pages: 20

Brands by name

Popular brands

Load more brands