manualshive.com logo in svg

GigaDevice Semiconductor GD32W515 Series, User Manual

The GigaDevice Semiconductor GD32W515 Series is a versatile and high-performance microcontroller designed for hardware development projects. Its comprehensive Hardware Development Manual is available for free download, providing enthusiasts with detailed instructions and insights. Unlock the full potential of this exceptional product by downloading the manual from manualshive.com.

Share
Download
background image

                                                                                                                 

GD32W51x User Manual

 

703 

 

 

0: Transmit  buffer DMA  is disabled. 

1: Transmit  buffer DMA  is enabled,  w hen the TBE  bit in SPI_STAT  is set, there w ill be a 

DMA  request  on corresponding  DMA  channel. 

0 

DMAREN 

Receive  buffer DMA  enable 

0: Receive buffer DMA  is disabled. 

1: Receive  buffer DMA  is enabled,  w hen the RBNE  bit in SPI_STAT  is set,  there w ill be 

a DMA  request on corresponding DMA  channel. 

20.11.3. 

Status register (SPI_STAT) 

Address offset: 0x08 

Reset value: 0x0000 0002 

This register can be accessed by half-word (16-bit) or word (32-bit). 

31

 

30

 

29

 

28

 

27

 

26

 

25

 

24

 

23

 

22

 

21

 

20

 

19

 

18

 

17

 

16

 

Reserved

 

 

15 

14 

13 

12 

11 

10 

9 

8 

7 

6 

5 

4 

3 

2 

1 

0 

Reserved 

FERR 

TRANS  RXORERR  CONFERR  CRCERR  TXURERR  I2SCH 

TBE 

RBNE 

 

rc_w0 

r 

r 

r 

rc_w0 

r 

r 

r 

r 

 

Bits   

Fields 

Descriptions  

31:9 

Reserved 

Must  be kept  at reset value. 

8 

FERR 

Format  error 

SPI  TI  Mode: 

0: No TI  mode  format error 

1: TI  mode  format error occurs 

I2S  Mode: 

0: No I2S  format error 

1: I2S  format error occurs 

This bit is set by hardw are and cleared by w riting 0. 

7 

TRANS 

Transmitting  ongoing  bit 

0: SPI  or I2S  is idle. 

1: SPI  or I2S  is currently transmitting  and/or receiving a frame 

This bit is set and cleared by hardw are. 

6 

RXORERR 

Reception  overrun error bit 

0: No reception overrun error occurs. 

1: Reception  overrun error occurs. 

This  bit  is set by hardw are and  cleared by a read  operation  on the  SPI_DATA  register  

follow ed by a read access to the SPI_STAT  register. 

5 

CONFERR 

SPI  Configuration  error 

Summary of Contents for GD32W515 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32W515 Series

Canon C50FSi - VB Network Camera Setup Manual preview
C50FSi - VB Network Camera
Brand: Canon Pages: 32
Rabbit 2000 Reference Manual preview
2000
Brand: Rabbit Pages: 120
Data Translation DT300 Series Getting Started Manual preview
DT300 Series
Brand: Data Translation Pages: 98
Safety Vision ROADRECORDER 8000 User Manual preview
ROADRECORDER 8000
Brand: Safety Vision Pages: 40
H3C S5120V3-EI Series Manual preview
S5120V3-EI Series
Brand: H3C Pages: 54
Ublox LENA-R8 Series System Integration Manual preview
LENA-R8 Series
Brand: Ublox Pages: 116
WHOOP WHT-25LT Quick Start Manual preview
WHT-25LT
Brand: WHOOP Pages: 26
HARTING HAIIC MICA Hardware Development Manual preview
HAIIC MICA
Brand: HARTING Pages: 13
Telit Wireless Solutions HE922-3GR Hardware User'S Manual preview
HE922-3GR
Brand: Telit Wireless Solutions Pages: 113
IDT DBP 7+4 User Manual preview
DBP 7+4
Brand: IDT Pages: 93
janitza Procont LMC-008-IO User Manual And Technical Data preview
Procont LMC-008-IO
Brand: janitza Pages: 28
Cameo WLG-1801 User Manual preview
WLG-1801
Brand: Cameo Pages: 23
Intel BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX Product Manual preview
BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX
Brand: Intel Pages: 86
XJTAG XJLink2-CFM User Manual preview
XJLink2-CFM
Brand: XJTAG Pages: 9
Xilinx Zynq-7000 Manual preview
Zynq-7000
Brand: Xilinx Pages: 8
ZALMAN CNPS5700D-Cu User Manual preview
CNPS5700D-Cu
Brand: ZALMAN Pages: 7
PairGain T1L2N20A Manual preview
T1L2N20A
Brand: PairGain Pages: 80
Freescale Semiconductor M68HC08 series Designer Reference Manual preview
M68HC08 series
Brand: Freescale Semiconductor Pages: 124

Brands by name

Popular brands

Load more brands