Korenix JetNet 7852G-4XG Series User Manual Download Page 861

Page: 861 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 861/1568

8.1.2

Configuration Commands

8.1.2.1

ip dvmrp

This command sets administrative mode of DVMRP in the router to active. IGMP must be
enabled before DVMRP can be enabled.

Syntax

ip dvmrp
no ip dvmrp

no -

This command sets administrative mode of DVMRP in the router to inactive. IGMP must

be enabled before DVMRP can be enabled.

Default Setting

Disabled

Command Mode

Global Config

This command sets the administrative mode of DVMRP on an interface to active.

Syntax

ip dvmrp
no ip dvmrp

no -

This command sets administrative mode of DVMRP on an interface to inactive.

Default
Setting

Disabled

Command

Mode

Interface Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands