Korenix JetNet 7852G-4XG Series User Manual Download Page 287

Page: 287 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 287/1568

This command sets the Edgeport BPDU Guard enable/disable parameter for accepting BPDUs on this
interface. This command only works on dot1d mode.

Syntax

spanning-tree bpduguard
no spanning-tree bpduguard

no -

This command sets the Edgeport BPDU Guard to the default value, that is, Disabled.

Default Setting

Disabled

Command Mode

Interface Config

6.4.2.13

spanning-tree uplinkfast

This command sets the Uplink Fast parameter to a new value on this switch. This command only works
on dot1d mode.

Syntax

spanning-tree uplinkfast
no spanning-tree uplinkfast

no -

This command sets the Uplink Fast parameter to the default value, that is Disabled.

Default Setting

Disabled

Command Mode

Global Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands