Korenix JetNet 7852G-4XG Series User Manual Download Page 1134 | Manualshive

Page: 1134 / 1568

background image

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1134/1568

sFlow Receiver Address

- The IP address of the sFlow collector.

sFlow Receiver Port

- The destination port for sFlow datagrams.

sFlow Receiver Datagram Version

- The version of sFlow datagrams that should be sent.

Command Buttons

Submit

- Send the updated data to the switch and cause the changes to take effect on the switch.

Refresh

- Refresh the data on the screen with present state of data in the switch.

11.2.14.3

Configuring sFlow Poller Configuration Page

sFlow agent collects time-based sampling of network interface statistics and sends them to the
configured sFlow receivers. A data source configured to collect counter samples is called a poller.

Selection Criteria

Poller Datasource(Slot/Port)

- sFlowDataSource for this sFlow sampler. This Agent will support

Physical ports only.

Configurable Data

Receiver Index

- The sFlowReceiver associated with this counter poller. Allowed range is (1 to 8 )

Poller Interval

- The maximum number of seconds between successive samples of the counters

associated with this data source. A sampling interval of 0 disables counter sampling. Allowed range
is (0 to 86400 secs)

Non-Configurable Data

Poller DataSource

- The interface for which data is being displayed.

Receiver Index

- The sFlowReceiver for this sFlow Counter Poller. If set to 0, the poller configuration

is set to default and the poller is deleted. Only active receivers can be set. If a receiver expires then
all pollers associated with the receiver will also expire. Allowed range is (1 to 8 )

Poller Interval

- The maximum number of seconds between successive samples of the counters

associated with this data source.

Command Buttons

Submit

- Send the updated data to the switch and cause the changes to take effect on the switch.

Refresh

- Refresh the data on the screen with present state of data in the switch.

«
...
1132
1133
1134
1135
1136
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

Firebox SOHO 6 Wireless

Brand: Watchguard Pages: 8

Brand: ADTRAN Pages: 2

Brand: Enginko Pages: 19

NetVanta 6355 PoE

Brand: ADTRAN Pages: 46

PoleVault System A/V Source Inputs

Brand: Extron electronics Pages: 4

Brand: Ravpower Pages: 27

301300U - Ethernet Disk NAS Server

Brand: LaCie Pages: 62

Brand: Quantum Pages: 7

Brand: Teldat Pages: 23

Brand: Ubiquiti Pages: 20

Brand: DPS Telecom Pages: 80

Brand: Allied Telesis Pages: 44

Brand: Planet Pages: 2

Brand: Lantech Pages: 20

Brand: socomec Pages: 54

StorageGRID Webscale SG5700 Series

Brand: NetApp Pages: 15

Brand: Westermo Pages: 22

Brand: RadioLAN Pages: 118

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands