Korenix JetNet 7852G-4XG Series User Manual Download Page 1517 | Manualshive

Page: 1517 / 1568

background image

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1517/1568

selected interface.

Startup Query Count

- The number of queries to be sent on startup.

Last Member Query Interval (1/10 of a sec)

- The last member query interval. The last member

query interval is the maximum response time inserted into group-specific queries sent in response
to leave group messages, and is also the amount of time between group-specific query messages.
This value may be tuned to modify the leave latency of the network. A reduced value results in
reduced time to detect the loss of the last member of a group. This value is not used for IGMP
version 1.

Last Member Query Count

- The number of queries to be sent on receiving a leave group report.

Interface Statistics

Querier

- The address of the IGMP querier on the IP subnet to which the selected interface

is attached.

Querier Status

- Indicates whether the selected interface is in querier or non querier mode.

Querier Up Time (hh:mm:ss)

- The time in seconds since the IGMP interface querier was

last changed.

Querier Expiry Time (hh:mm:ss)

- The time in seconds remaining before the other querier

present timer expires. If the local system is the querier, this will be zero.

Wrong Version Queries Received

- The number of queries that have been received on the

selected interface with an IGMP version that does not match the IGMP version configured for the
interface, over the lifetime of the entry. IGMP requires that all routers on a LAN be configured to
run the same version of IGMP. Therefore, a configuration error is indicated if any queries are
received with the wrong version number.

Number of Joins Received

- The number of times a group membership has been added on

the selected interface; that is, the number of times an entry for this interface has been added to
the cache table. This gives an indication of the amount of IGMP activity on the interface.

Number of Groups

- The current number of entries for the selected interface in the cache table.

Command Buttons

Refresh

- Refresh the data on the screen with the present state of the data in the switch.

«
...
1515
1516
1517
1518
1519
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

Brand: Lab.gruppen Pages: 35

Brand: TP-Link Pages: 2

Active Module Carrier VX402C-64

Brand: C&H Pages: 32

Brand: Zhone Pages: 53

Brand: Linksys Pages: 80

Network Adapter AC AAP

Brand: Extron electronics Pages: 2

DiskStation Series

Brand: Synology Pages: 6

Brand: Allied Telesis Pages: 2

Brand: H3C Pages: 46

Brand: National Instruments Pages: 72

Brand: NetApp Pages: 95

Brand: Crestron Pages: 8

Brand: D-Link Pages: 141

Brand: D-Link Pages: 72

Brand: Canon Pages: 8

Brand: Canon Pages: 11

PIXMA MP495 Series

Brand: Canon Pages: 24

Brand: Canon Pages: 288

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands