Korenix JetNet 7852G-4XG Series User Manual Download Page 963

Page: 963 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 963/1568

9.3.2.16

ipv6 nd router-preference

This command sets the router preference for Default Router.

Syntax

ipv6 nd router-preference <high | low | medium>
no ipv6 nd router-preference

–

This command resets router preference to default.

Default Setting

Medium

Command Mode

Interface Config

9.3.2.17

ipv6 nd suppress-ra

This command suppresses router advertisement transmission on an interface.

Syntax

ipv6 nd suppress-ra
no ipv6 nd suppress-ra

–

This command enables router transmission on an interface.

Default Setting

Disabled

Command Mode

Interface Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands