Korenix JetNet 7852G-4XG Series User Manual Download Page 389

Page: 389 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 389/1568

6.9.4.47

Captive Portal configuration label name for accounting identification

This command is to Captive Portal configuration label name for accounting identification.

Syntax

account-label <UTF-16>

no account-label

Default Setting

None

Command Mode

Captive Portal Locale Mode

6.9.4.48

Captive Portal configuration Acceptance Use Policy

This command is to Captive Portal configuration Acceptance Use Policy.

Syntax

aup-text <UTF-16>

no aup-text

Default Setting

None

Command Mode

Captive Portal Locale Mode

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands