Korenix JetNet 7852G-4XG Series User Manual Download Page 1123

Page: 1123 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1123/1568

Port ID Subtype

- Specifies the source of port identifier.

Port ID

- Specifies the port component associated with the remote system.

System Name

- Specifies the system name of the remote system.

System Description

- Specifies the description of the given port associated with the remote system.

Port Description

- Specifies the description of the given port associated with the remote system.

System Capabilities Supported

- Specifies the system capabilities of the remote system.

System Capabilities Enabled

- Specifies the system capabilities of the remote system which are

supported and enabled.

Time to Live

- Specifies the Time To Live value in seconds of the received remote entry.

Management Address



Management Address

- Specifies the advertised management address of the remote

system.



Type

- Specifies the type of the management address.

MAC/PHY Configuration/Status



Auto-Negotiation

- Specifies whether the auto-negotiation is supported and whether the

auto-negotiation is enabled.



PMD Auto-Negotiation Advertised Capabilities

- Specifies the auto-negotiation and speed

capabilities of the PMD.



Operational MAU Type

- Specifies the current duplex and speed settings of the sending

system.

Power Via MDI



MDI Power Support

- Specifies the MDI power support capabilities of the sending IEEE

802.3 LAN station.



PSE Power Pair

- Specifies which pair is powered.



Power Class

- Specifies the required power level required.

Link Aggregation Status

- Specifies the capability and current aggregation status of the link.

Link Aggregation Port Id

- Specifies the aggregated port identifier.

Maximum Frame Size

- Specifies the maximum supported IEEE 802.3 frame size.

Port VLAN Identity

- Specifies the VLAN ID of the port.

Protocol VLAN

- Specifies the Protocol VLAN ID and status.

VLAN Name

- Specifies the VLAN name.

Protocol Identity

- Specifies the particular protocols that are accessible through the port.

Command Buttons

Refresh

- Updates the information on the page.

«
...
1121
1122
1123
1124
1125
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands