Korenix JetNet 7852G-4XG Series User Manual Download Page 1113

Page: 1113 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1113/1568

11.2.11

Managing UDLD

11.2.11.1

Configuring UDLD

Selection Criteria

Global Port Mode

- Specifies the UDLD Global Port mode. It has three options: Disable, Normal and

Aggressive.

Interface

- Specifies the list of all the physical ports on which UDLD can be configured.

Port Mode

- Specifies the UDLD Port mode for the selected interface. It has three options: Disable,

Normal and Aggressive.

Configurable Data

Message

- Specifies the Message Interval in seconds to send of messages in steady state. The

range is from (7 to 90). Default value is 15 seconds.

Command Buttons

Submit

- Send the updated screen to the switch and cause the changes to take effect on the switch

but these changes will not be retained across a power cycle unless a save is performed.

«
...
1111
1112
1113
1114
1115
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands