Korenix JetNet 7852G-4XG Series User Manual Download Page 580 | Manualshive

Page: 580 / 1568

background image

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 580/1568

6.21.3.1

assign-queue

This command modifies the queue id to which the associated traffic stream is assigned. The queueid is
an integer from 0 to n-1, where n is the number of egress queues supported by the device.

Syntax

assign-queue <0-7>

<0-7> -

Queue ID.

Command Mode

Policy-Class-Map Config

Incompatibilities

Drop

6.21.3.2

drop

This command specifies that all packets for the associated traffic stream are to be dropped at ingress.

Syntax

drop

Command Mode

Policy-Class-Map Config

Incompatibilities

Assign Queue, Mark (all forms), Mirror, Police, Redirect

«
...
578
579
580
581
582
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

Verizon DSL-2750B

Brand: D-Link Pages: 2

Brand: D-Link Pages: 4

Brand: Habitat Pages: 48

Brand: Magnadyne Pages: 13

InterReach Fusion ADCP-77-044

Brand: TE Connectivity Pages: 236

Brand: CSS Pages: 2

Brand: Usr Pages: 2

totalstorage 200

Brand: IBM Pages: 152

Brand: Zalip Pages: 77

EtherFast LNE100TX ver. 5

Brand: Linksys Pages: 42

Brand: UTStarcom Pages: 71

Brand: Zoom Pages: 31

Brand: ivideon Pages: 11

Brand: PRIZM Pages: 8

Brand: Airvana Pages: 90

Airborne M2M ABDN-er-DP55 Series

Brand: B+B SmartWorx Pages: 120

AirBridge VS-YOFIMN-000

Brand: Vivint Pages: 2

Brand: ADTRAN Pages: 136

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands