Korenix JetNet 7852G-4XG Series User Manual Download Page 488 | Manualshive

Page: 488 / 1568

background image

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 488/1568

6.16.2

Configuration Commands

6.16.2.1

macfilter

This command adds a static MAC filter entry for the MAC address <macaddr> on the VLAN <vlanid>.
The value of the <macaddr> parameter is a 6-byte hexadecimal number in the format of
b1:b2:b3:b4:b5:b6.

The restricted MAC Addresses are: 00:00:00:00:00:00, 01:80:C2:00:00:00 to 01:80:C2:00:00:0F,
01:80:C2:00:00:20 to 01:80:C2:00:00:21, and FF:FF:FF:FF:FF:FF. The <vlanid> parameter must identify
a valid VLAN. You can create up to 100 static MAC filters.

Syntax

macfilter <macaddr> <1-4093>
no macfilter <macaddr> <1-4093>

<macaddr> -

Specified a 6-byte hexadecimal number in the format of b1:b2:b3:b4:b5:b6.

no -

This command removes all filtering restrictions and the static MAC filter entry for the MAC

address <macaddr> on the VLAN <vlanid>.

Default Setting

None

Command Mode

Global Config

«
...
486
487
488
489
490
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

Power Xpert Meter 2000

Brand: Eaton Pages: 16

POW-R-COMMAND 1000

Brand: Eaton Pages: 84

Brand: Konig Pages: 73

Brand: Ruckus Wireless Pages: 56

Brand: I-O Wireless Pages: 55

BIC 1I12-P2A25-M30MI1-BPX05-110

Brand: Balluff Pages: 12

Brand: E-TOP Pages: 24

Brand: Intellinet Pages: 12

Brand: ICP DAS USA Pages: 62

Brand: Techroutes Pages: 20

NetVanta Serial Dial Backup Interface Module (DIM) none

Brand: ADTRAN Pages: 2

Brand: CopperOptics Pages: 12

Brand: Thecus Pages: 130

Vigor 3200 Series

Brand: Draytek Pages: 356

Brand: RSupport Pages: 5

Brand: NETGEAR Pages: 2

Brand: Billion Pages: 20

Brand: Hitachi Pages: 208

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands