Korenix JetNet 7852G-4XG Series User Manual Download Page 384

Page: 384 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 384/1568

6.9.4.37

Captive Portal configuration RADIUS authentication server

Use this command to configure a captive portal configuration RADIUS authentication server.

Syntax

radius-auth-server <server-name>

no radius-auth-server

Default Setting

Disable

Command Mode

Captive Portal Instance

6.9.4.38

Enable/Disable Captive Portal configuration redirect mode

This command enables the redirect mode for a captive portal configuration.

Syntax

redirect

no redirect

Default Setting

Disable

Command Mode

Captive Portal Instance

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands