Korenix JetNet 7852G-4XG Series User Manual Download Page 1131

Page: 1131 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1131/1568

Manufacturer Name

- Specifies manufacturer

’s name of the remote device.

Model Name

- Specifies model name of the remote device.

Asset ID

- Specifies asset id of the remote device.

Location Information

- Specifies if location TLV is received in LLDP frames on this port.

Sub Type

- Specifies type of location information.

Location Information

- Specifies the location information as a string for given type of location id.

Extended PoE

- Specifies if remote device is a PoE device.

Device Type

- Specifies remote device's PoE device type connected to this port.

Extended PoE PSE

- Specifies if extended PSE TLV is received in LLDP frame on this port.

Available

- Specifies the remote ports PSE power value in tenths of watts.

Source

Specifies the remote ports PSE power source.

Priority

- Specifies the remote ports PSE power priority.

Extended PoE PD

- Specifies if extended PD TLV is received in LLDP frame on this port.

Required

- Specifies the remote port's PD power requirement.

Source

Specifies the remote port's PD power source.

Priority

Specifies the remote port's PD power priority.

Command Buttons

Refresh

- Updates the information on the page.

«
...
1129
1130
1131
1132
1133
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands