Korenix JetNet 7852G-4XG Series User Manual Download Page 1494

Page: 1494 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1494/1568

11.7.8

Managing IPv6 Routes

11.7.8.1

Configuring IPv6 Route Entry Configuration Page

Selection Criteria

Interface

- Enter the unit, slot and port number for the Link-local IPv6 Next Hop Address. This field is

displayed only if Link-local Next-hop Selector is selected as Link-local.

Route Type

- Specify if the Next Hop IPv6 Address is a Global IPv6 Address or a Link-local IPv6

Address or a Static-Reject IPv6 Address.

Configurable Data

IPv6 Network Prefix-

Enter an IPv6 Network Address Prefix.

IPv6 Network Prefix Length

- Enter the IPv6 Network Address Prefix Length.

Next Hop IPv6 Address

- Enter an IPv6 Next Hop Address. If the Next Hop IPv6 Address specified

is a Link-local IPv6 Address, specify the Slot/Port for the Link-local IPv6 Next Hop Address.

Preference

- Enter a Preference Value for the given route. It is optional. If left blank, the preference

value configured for the static route type is picked up for the route. The valid range is (1 to 255).

Command Buttons

Submit

- Send the updated configuration to the switch. Configuration changes take effect

immediately. These changes will not be retained across a power cycle unless a save is performed.

Cancel

- Discards the changes made on the page and navigates back to the referring page.

«
...
1492
1493
1494
1495
1496
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands