Korenix JetNet 7852G-4XG Series User Manual Download Page 435

Page: 435 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 435/1568

This command is used to enable CDP for all interfaces.

Syntax

cdp run all
no cdp run all

all -

All interfaces.

no -

This command is used to disable CDP for all interfaces.

Default Setting

Enabled

Command Mode

Global Config

6.10.2.3

cdp timer

This command is used to configure an interval time (seconds) of the sending CDP packet.

Syntax

cdp timer <5-254>
no cdp timer

<5-254> -

interval time (Range: 5

– 254).

no -

This command is used to reset the interval time to the default value.

Default Setting

Command Mode

Global Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands