Korenix JetNet 7852G-4XG Series User Manual Download Page 1556

Page: 1556 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1556/1568

11.9.2.4

Viewing Interface

’s PIM Configuration Page

Selection Criteria

Interface

- Select the interface for which data is to be displayed.

Non-Configurable Data

Admin Mode

- The administrative mode of PIM-SM interface in the router: either enable or disable.

Protocol State

- The state of PIM in the router: either operational or non-operational.

IP Address

- The IP address of the selected PIM interface.

Hello Interval (secs)

- The frequency (in seconds) at which PIM hello messages are transmitted

on the selected interface.

Join/Prune Interval (secs)

- The frequency (in seconds) at which PIM Join/Prune messages

are transmitted on this PIM interface. This field is always shown with defaults for PIMDM as
configurability is not supported in PIMDM.

DR Priority

- Indicates the DR priority on the PIM interface. This field is supported in PIMSM

only and hence shown for PIMSM only.

BSR Border

- Specifies the BSR border mode on the PIM interface. This field is supported in

PIMSM only and hence shown for PIMSM only.

Designated Router

- The Designated Router on the selected PIM interface. This field is

supported in PIMSM only and hence shown for PIMSM only. This field is displayed only when the

«
...
1554
1555
1556
1557
1558
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands