Korenix JetNet 7852G-4XG Series User Manual Download Page 163

Page: 163 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 163/1568

6.2.10.11

lacp actor or lacp partner

This command set <actor | partner> admin key value of Link Aggregation Control Protocol (LACP) on a
port.

Syntax

lacp <actor|partner> admin key <key-value>
no lacp <actor|partner> admin key

<key-value>

: 0-65535

- This command restores <actor | partner> admin key value of Link Aggregation Control Protocol

(LACP) on a port.

Default Setting

Interface Number

Command Mode

Interface Config

This command set <actor | partner> admin state value of Link Aggregation Control Protocol (LACP) on a
port.

Syntax

individual

- Set lacp admin state to individual. Use no form to set to aggregation.

longtimeout

- Set lacp admin state longtimeout. Use no form to set to shorttimeout.

passive -

Set lacp admin state passive. Use no form to set to active.

no -

This command restores <actor | partner> admin state value of Link Aggregation Control

Protocol (LACP) on a port.

Default Setting

no lndividual (aggregation)

no longtimeout (shorttimeout)

no passive (active)

Command Mode

Interface Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands