Korenix JetNet 7852G-4XG Series User Manual Download Page 427 | Manualshive

Page: 427 / 1568

background image

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 427/1568

6.9.8.2.15 dos-control tcpflagseq

This command enables the TCP Control Flags=0 and SEQ=0 checking Denial of Service protections. If
the mode is enabled, Denial of Service prevention is active for this type of attack. If packets ingress
having TCP Control Flags set to 0 and TCP Sequence Number set to 0, the packets will be dropped if
the mode is enabled.

Syntax

dos-control tcpflagseq
no dos-control tcpflagseq

no -

This command disables the TCP Control Flags=0 and SEQ=0 checking Denial of Service

protections.

Default Setting

Disabled

Command Mode

Global Config

6.9.8.2.16 dos-control tcpsyn

This command enables the TCP SYN and L4 source port = 0-1023 Denial of Service protection. If the
mode is enabled, Denial of Service prevention is active for this type of attack. If packets ingress having
TCP flag SYN set and an L4 source port from 0 to 1023, the packets will be dropped if the mode is
enabled.

Syntax

dos-control tcpsyn
no dos-control tcpsyn

no -

This command disables the TCP SYN and L4 source port = 0-1023 Denial of Service protection.

Default Setting

Disabled

Command Mode

Global Config

«
...
425
426
427
428
429
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

Brand: Amperes Pages: 8

Brand: Klark Teknik Pages: 50

AyrMesh IndoorAP

Brand: AYRSTONE Pages: 2

Brand: Variscite Pages: 18

Brand: UfiSpace Pages: 32

AirStation WZR-1166DHP

Brand: Buffalo Pages: 2

Brand: B&B Electronics Pages: 2

Brand: Global Sun Pages: 39

Brand: Razer Pages: 17

Brand: Topcom Pages: 16

Brand: LevelOne Pages: 3

Brand: TP-Link Pages: 4

Brand: DPS Pages: 57

IP Board IPT10000C

Brand: Dialogic Pages: 2

Brand: Altimium Pages: 12

Security Router X-PeditionTM

Brand: Enterasys Pages: 466

TeraStation WSS WS5020N6

Brand: Buffalo Pages: 115

Brand: N-Tron Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands