Korenix JetNet 7852G-4XG Series User Manual Download Page 182

Page: 182 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 182/1568

6.2.14.3

link state group

Set upstream port or downstream port for a link state group. Use

‘link state group <group id> upstream’

to set the port to be monitored.

Syntax

link state group <1-6> {downstream | upstream}
no link state group <1-6> {downstream | upstream}

no -

This command disables link state group function.

Command Mode

Interface Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands