Korenix JetNet 7852G-4XG Series User Manual Download Page 151

Page: 151 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 151/1568

6.2.9.8

ipv6 mld snooping querier vlan

The user can go to the CLI Global Configuration Mode to set MLD snooping querier vlan admin mode,
use the

ipv6 mld snooping querier vlan <vlanid>

global configuration command. Use the

no ipv6 mld

snooping querier vlan <vlanid>

return to disable.

Syntax

ipv6 mld snooping querier vlan <vlanid>
no ipv6 mld snooping querier vlan <vlanid>

<vlanid>

- VLAN ID (Range: 1

– 4093).

Default Setting

Disabled

Command Mode

Global Config

6.2.9.9

ipv6 mld snooping querier vlan address

The user can go to the CLI Global Configuration Mode to set MLD snooping querier vlan address, use
the

ipv6 mld snooping querier vlan <vlanid> address <ip-address>

global configuration command.

Use the

no ipv6 mld snooping querier vlan <vlanid> address <ip-address>

return to default value

zero.

Syntax

ipv6 mld snooping querier vlan <vlanid> address <ipv6-address>
no ipv6 mld snooping querier vlan <vlanid> address <ipv6-address>

<vlanid>

- VLAN ID (Range: 1

– 4093).

<ipv6-address>

- The IPv6 address will be used in the IPv6 header while sending out MLD queries

on this VLAN.

Default Setting

Disabled

Command Mode

Global Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands