Korenix JetNet 7852G-4XG Series User Manual Download Page 1203

Page: 1203 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1203/1568

11.3.17.4

Configuring DAI ARP ACL Configuration Page

Configurable Data

ARP ACL Name

- This is used to create New ARP ACL for DAI.

Remove

- This is used to select the particular ACLs which you want to delete.

Non-Configurable Data

ARP ACL Name

- This will list all the configured ARP ACL List.

Command Buttons

Add

- This is used to create New ARP ACL.

Delete

- This is used to delete the entries selected using checkbox under Remove field.

Refresh

- Refresh the data on the screen with the present state of the data in the switch.

«
...
1201
1202
1203
1204
1205
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands