Korenix JetNet 7852G-4XG Series User Manual Download Page 284

Page: 284 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 284/1568

6.4.2.11

spanning-tree auto-edge

This command sets the auto-edge for this port to enabled.

Syntax

spanning-tree auto-edge
no spanning-tree auto-edge

no -

This command sets the auto-edge for this port to disabled.

Default Setting

Disabled

Command Mode

Interface Config

6.4.2.12

spanning-tree edgeport

This command sets the edguport function to Enabled or Disabled on this switch.

Syntax

spanning-tree edgeport
no spanning-tree edgeport

no -

This command sets the Edgeport function to the default value, that is Enabled.

Default Setting

Enabled

Command Mode

Global Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands