Korenix JetNet 7852G-4XG Series User Manual Download Page 140

Page: 140 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 140/1568

6.2.8.7

clear mld snooping

The user can go to the CLI Global/Interface Configuration Mode to clear MLD Snooping on the system,
use the

clear mld snooping

priviledge configuration command.

Syntax

clear mld snooping

Default Setting

None

Command Mode

Privilege Exec

6.2.8.8

ipv6 mld snooping interfacemode

The user can go to the CLI Global/Interface Configuration Mode to set MLD Snooping on one interface
or all interfaces, use the

ipv6 mld snooping interfacemode

to enable MLD snooping on

global/interface. Use the

no ipv6 mld snooping interfacemode

to disable MLD Snooping on global/

interfaces.

Syntax

Ipv6 mld snooping interfacemode [<all>]
no ipv6 mld snooping interfacemode [<all>]

Default Setting

Disabled

Command Mode

Global Config

Interface Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands