Korenix JetNet 7852G-4XG Series User Manual Download Page 1190

Page: 1190 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1190/1568

Configurable Data

MAC Address -

Specify the MAC Address for the new Voice VLAN. (You can only enter data in this

field when you are creating a new Voice VLAN.).

MAC Address Mask -

Use this optional field to specify a mask for the Voice VLAN. The mac-mask is

the last eight digit of the mask code of the MAC address, the valid values are: 0xff, 0xfe, 0xfc, 0xf8,
0xf0, 0xe0, 0xc0, 0x80 and 0x0.

Voice-VLAN Priority -

This field identifies the priority of the Voice VLAN you are configuring. The

priority-id is the priority of the voice traffic; the valid range is 0 to 7.

Voice VLAN Name -

Use this field to specify the name of the voice device. It is to help the device

management.

Command Buttons

Submit

- Update the switch with the values on this screen. If you want the switch to retain the new

values across a power cycle, you must perform a save.

Delete

- Delete this VLAN. You are not allowed to delete the default VLAN.

11.3.12.3

Viewing MAC-based Voice VLAN Information Page

This page displays the status of all currently configured Voice VLANs.

Non-Configurable Data

Voice-VLAN Name -

The name of the voice device.

MAC Address -

The MAC Address for the new Voice VLAN.

MAC Address Mask -

The MAC Address Mask for the Voice VLAN. The value is the last eight digit

of the mask code of the MAC address.

Voice-VLAN Priority -

The priority-id is the priority of the voice traffic.

«
...
1188
1189
1190
1191
1192
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands