Korenix JetNet 7852G-4XG Series User Manual Download Page 1304

Page: 1304 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1304/1568

11.4.3.18

Captive Portal Client Statistics Page

Non-Configurable Data

Bytes Transmitted

- Total bytes the client has transmitted.

Bytes Received

- Total bytes the client has received.

Packets Transmitted

- Total packets the client has transmitted.

Packets Received

- Total packets the client has received

Command Buttons

Refresh

- Refresh the data on the screen with the present state of the data in the switch.

«
...
1302
1303
1304
1305
1306
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands